Results 211 to 220 of about 48,328 (261)

Effects of Grinding Parameters on Creep Feed Grinding

Advanced Materials Research, 2013
Creep feed grinding can obtain an excellent grinding performance for its creep feed with high depth of cutting. However the large contact length and large feed result in large amount of heat accumulating in working zone and cause burn on workpiece surface.
openaire   +1 more source

Effects of grinding parameters on product fineness in jet mill grinding

Minerals Engineering, 1998
Abstract The influence of several grinding parameters on the product fineness in jet mill grinding was studied experimentally with a laboratory scale spiral type jet mill. The most significant variables in the jet mill grinding were feed rate, volumetric flow rate of grinding air and the height of an inside classification tube for grinding at ...
R. Tuunila, L. Nyström
openaire   +1 more source

Finite element analysis of influence of grinding parameters on grinding force

Proceedings of 2011 International Conference on Electronic & Mechanical Engineering and Information Technology, 2011
In this paper, based on the three-dimensional finite element model of surface grinding, the finite element analysis was employed to analyze the influence of grinding parameters on grinding force during the machining of SiCp/Al composites using diamond grinding wheel. The results indicate that model can reflect tendency of grinding force.
openaire   +1 more source

Modeling and Analysis of the Grinding Parameters

Applied Mechanics and Materials, 2011
Efficient grinding of structural ceramics requires judicious selection of operating parameters to maximize removal rate while controlling surface integrity. Grinding of ceramics is difficult because of its low fracture toughness, making it very sensitive to cracking.
openaire   +1 more source

Effects of grinding parameters on surface quality in silicon nitride grinding

Ceramics International, 2017
Abstract To reveal the effects of the grinding parameters on the ground surface quality of silicon nitride grinding to guide processing for improving the processing accuracy and productivity, orthogonal experiments on silicon nitride grinding are carried out by a diamond grinding wheel, and the effects are studied systematically.
Wei Liu, Zhaohui Deng, Yuanyuan Shang, Linlin Wan   +3 more
openaire   +1 more source

The correlation of process parameters in grinding

Wear, 1990
Abstract An energy method, which had previously been shown to represent well the cutting action of model abrasive grits, was combined with the usual relationships of grinding mechanics to obtain a mathematical model of grinding forces and surface roughness.
openaire   +1 more source

Process Parameters and Residual Stresses in Cylindrical Grinding

Journal of Manufacturing Science and Engineering, 2002
The paper presents an experimental study on the relationship between process parameters and residual stresses in cylindrical grinding. In particular, the influence of the depth of cut (a) and the peripheral velocity of the workpiece vw was investigated.
CAPELLO, EDOARDO, SEMERARO, QUIRICO
openaire   +2 more sources

Research on the adaptive adjustment of the parameters in grinding process

2016 IEEE International Conference on Information and Automation (ICIA), 2016
The grinding process is influenced by many factors which make it prone to fluctuations in the quality and hard to guarantee the effectiveness and reliability. Therefore, as for this problem, an adaptive adjustment model of the parameters in grinding process is established.
Junde Qi, Dinghua Zhang, Shan Li, Bing Chen   +3 more
openaire   +1 more source

Influence of Grinding Parameters on the Depth and Uniformity of Cylindrical Grinding-Hardened Layer

Advanced Materials Research, 2010
On the basis of the cylindrical grinding-hardening test, the influences of the grinding parameters on surface hardened layer were studied. The result shows that when ap≤0.2mm, there is an unhardened area exist in cylindrical grinding hardened workpiece.
Ju Dong Liu, Jie Zhen Zhuang, Xi Lin Zhang, Zhi Long Xu   +3 more
openaire   +1 more source

Belt Grinding Simulation to Optimize Manual Grinding Process Parameters

Volume 2: Functional Devices/Bioinspired Structures; Sustainability; Semiconductor Manufacturing; Surface Engineering; Clean Energy and E-Mobility Manufacturing; Machining and Deformation Processes; Welding and Joining Processes of Advanced Materials and Structures; Equipment Design, Control and Automation; Human Integration to Smart Manufacturing Systems; Thin Films and Coatings; Meso, Micro, Nano Subtractive and Formative Manufacturing; Explainable AI for Knowledge Discovery
Abstract Abrasive belt grinding is a manufacturing process used to finish the surface of materials. This process uses abrasive particles of geometrically undefined cutting edges bonded to a flexible cloth. Abrasive belt grinding is often performed manually (manual grinding), and a skilled operator can achieve high quality on complex ...
Felicia F. Fashanu, Brandon Gee, Barbara S. Linke   +2 more
openaire   +1 more source