Results 21 to 30 of about 221,637 (307)
Modeling and Numerical Simulation of the Grinding Temperature Field with Nanoparticle Jet of MQL
Advances in Mechanical Engineering, 2013 In this research, the heat transfer model of surface grinding temperature field with nanoparticle jet flow of MQL as well as the proportionality coefficient model of energy input workpiece was established, respectively.
C. H. Li, J. Y. Li, S. Wang, Q. Zhang
doaj +1 more source
Jin'gangshi yu moliao moju gongcheng, 2022 In view of frequent dressing of grinding wheel in process of centerless cylindrical grinding of micromotor rotor shaft, this paper proposes to use microcrystalline ceramic corundum grinding wheel instead of traditional corundum grinding wheel to grind ...
Bisheng ZHANG, Yao WU, Meina QU
doaj +1 more source
Profile Gear Grinding Temperature Reduction and Equalization [PDF]
Journal of Engineering Sciences, 2018 The profile gear grinding modes definition technique is developed to provide the uniform residual temperatures after heating and subsequent cooling which predetermine uniform thermal deformations on periphery of a cogwheel when grinding. The initial basis for this is a possibility to determine the gear grinding temperature both on the heating and ...
Lishchenko, N.V., Larshin, V.P.
openaire +2 more sources
On the interest of using degradable fillers in co-ground composite materials [PDF]
, 2009 The article presents the results of a study whose objective is to show the interest of using vegetable and biodegradable fillers in composite materials.
Le Bolay, Nadine +2 more
core +3 more sources
Grinding Characteristics of MoS2-Coated Brazed CBN Grinding Wheels in Dry Grinding of Titanium Alloy
Chinese Journal of Mechanical Engineering, 2023 As an important green manufacturing process, dry grinding has problems such as high grinding temperature and insufficient cooling capacity. Aiming at the problems of sticking and burns in dry grinding of titanium alloys, grinding performance evaluation ...
Junshuai Zhao +6 more
doaj +1 more source
Micromachines, 2022 Vitrified bond cubic boron nitride (CBN) grinding wheel specimens with controllable porosity were prepared by regulating the pore former dextrin content and varying the forming pressure, and the performance of the grinding camshaft was studied.
Qiao Xu +5 more
doaj +1 more source
PROFILE GEAR GRINDING TEMPERATURE DETERMINATION
Transactions of Kremenchuk Mykhailo Ostrohradskyi National University, 2018 The paper is devoted to solving an important scientific and technical problem of determining the profile gear grinding temperature based on the choice of simple but at the same time adequate solution from the available analytical ones. The initial prerequisite for the paper developing concept is that of a moving heat source, which was originally ...
N. V. Lishchenko, V. P. Larshin
openaire +2 more sources
Lubricants, 2023 Grinding fluid often struggles to enter the grinding area and overcoming this challenge has been a major focus of research in recent years. Therefore, CNTs@T304 nano-capsules are prepared by filling the cavities of CNTs with a lubricant of T304.
Jiju Guan +5 more
doaj +1 more source
Interrelation of heat process parameters during depth grinding with treatment quality [PDF]
, 2019 Аналитически определены параметры теплового процесса глубинного шлифования, включая температуру резания, глубину проникновени я тепла в поверхностный слой обрабатываемой детали, градиент температуры, и установлены основные условия их уменьшения с целью ...
Полянский, Владимир Иванович
core +1 more source
Matrix-filler interactions in a co-ground ecocomposite: surface properties and behaviour in water [PDF]
, 2011 Ecocomposites made up of polystyrene and starch were produced by co-grinding. The mechanism by which the composite is formed was identified by following the particle size and morphology.
Lamure, Alain +2 more
core +2 more sources