Results 41 to 50 of about 13,352 (253)

Hydrogen‐Assisted Fracture of Iron‐Based Fe–Ni–Al Alloys

Advanced Engineering Materials, EarlyView.
Principal relations and fracture mechanisms of single‐phase and precipitate‐strengthened Fe–Ni–Al alloys subjected to prior electrochemical hydrogen charging are identified. The mechanisms of hydrogen effect on strength and microhardness are discussed, including hydrogen‐induced increase in microhardness and the role of hydrogen in fracture behavior ...
Nataliya Yadzhak, Olha Zvirko, Rostyslav Leshchak, Hryhoriy Nykyforchyn   +3 more
wiley   +1 more source

Abrasive machining simulation technology for hard-brittle materials

Jin'gangshi yu moliao moju gongcheng, 2019
Hard-brittle materials such as monocrystalline silicon have high hardness, low fracture toughness and other characteristics, which belong to difficult-to-machine materials.
LI Long, GE Peiqi, WANG Peizhi, LI Zongqiang   +3 more
doaj  

On Strength of Brittle Nanomaterials: Confinement Effect on Weibull Distributions

Frontiers in Materials, 2019
Recent progress in nanotechnology enables us to utilize elastic strain engineering, the emerging technology capable of controlling the physio-chemical properties of materials via externally-imposed elastic strains, for hard materials.
Dahye Shin, Dongchan Jang
doaj   +1 more source

Creep Properties and Deformation Mechanism of Additively Manufactured NiAl‐CrMo Composites

Advanced Engineering Materials, EarlyView.
Additively manufactured NiAl‐CrMo composites contain numerous interfaces and cell boundaries that control their creep response. At 700°C under high applied stress, creep is dominated by dislocation‐controlled power‐law mechanisms. At 800°C–900°C and lower stresses, creep is primarily diffusion‐controlled along cell boundaries.
Jan Vollhüter, Andreas Bezold, Johan Westraadt, Katharina Fiegl, Subham Chattoraj, Benjamin Wahlmann, Carolin Körner, Michael Mills, Mathias Göken, Steffen Neumeier   +9 more
wiley   +1 more source

Microstructure, Thermal Transport, and Dry‐Sliding Tribology of Powder‐Metallurgy Al7075 Composites Reinforced With Sol–Gel‐Derived ZnO–rGO Hybrid Nanoparticles

Advanced Engineering Materials, EarlyView.
Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal, Cevher Kursat Macit, Merve Ayık, Hakan Tutumlu   +3 more
wiley   +1 more source

Active Corrosion Protection of Sintered AA7075 Aluminum Alloy via Mn Powder Addition

Advanced Engineering Materials, EarlyView.
AA7075 containing Mn‐rich particles is fabricated via spark plasma sintering using AA7075 and Mn powders. Corrosion resistance is evaluated through dip‐and‐dry tests using 0.1 M NaCl (pH 6.0), and mass loss decreases with increasing Mn addition. Mn‐rich particles function as a source of Mn ions, and formation of Mn‐accumulation films on Cu‐containing ...
Ko Ebina, Masashi Nishimoto, Izumi Muto
wiley   +1 more source

Additive Manufacturing of Alumina‐Reinforced Elastomers

Advanced Engineering Materials, EarlyView.
Vat‐photopolymerized elastomers reinforced with platelet‐shaped alumina exhibited preferential orientation, reduced porosity, and significantly enhanced mechanical performance. A 3 wt% platelet loading increased tensile strength from 12.4 to 45.7 MPa, highlighting the critical role of filler morphology in elastomeric VPP composites.
Majid Barzegar Keyvani, Zongwen Fu, Robert Göstl, Hamed Shokri, Carmine Putignano, Gianluca Percoco, Bilal Gökce   +6 more
wiley   +1 more source

Development of a Novel Ultrasonic Drill Using Longitudinal-Bending Hybrid Mode

IEEE Access, 2017
Machining of hard and brittle materials is usually troublesome due to their high stiffness. In order to improve the processing speed of hard and brittle materials, ultrasonic assisted processing was developed.
Xintian Tang, Yingxiang Liu, Shengjun Shi, Weishan Chen, Xinda Qi   +4 more
doaj   +1 more source

Extrusion‐Based Additive Manufacturing of Advanced Ceramics: Strengthening Mechanisms and Process Optimization Review

Advanced Engineering Materials, EarlyView.
This review comprehensively evaluates extrusion‐based additive manufacturing for advanced ceramics, detailing feedstock options and key process parameters. By critically addressing defect mechanisms like porosity and cracking, the work highlights optimization strategies through machine learning and advanced postprocessing.
Meisam Bakhtiari, Mohammad Hadi Sheikh‐Ansari, Avinash Borgaonkar, Mehran Dadkhah, Abdollah Saboori   +4 more
wiley   +1 more source

Impact of MgO Additions on the Oxidation Resistance and Compression Behavior of Vanadium Alloys

Advanced Engineering Materials, EarlyView.
An increase in oxidation resistance at 600 °C is achieved for alloys containing more than 2.5 wt.% MgO. It has been established that, along with V2O5, MgO6V2, and Mg2O7V2 are formed, which are presumed to enhance oxidative stability. Furthermore, the possible transformation of Mg‐vanadates through reaction with CO2, which presumably occurs in this ...
Ievgen Solodkyi, Mathias Galetz, Georg Hasemann, Fabian Lanoy, Emma White, Manja Krüger   +5 more
wiley   +1 more source