Results 51 to 60 of about 80,804 (296)
Advanced Engineering Materials, EarlyView.Herein, environmental scanning electron microscopy (ESEM) is discussed as a powerful extension of conventional SEM for life sciences. By combining high‐resolution imaging with variable pressure and humidity, ESEM allows the analysis of untreated biological materials, supports in situ monitoring of hydration‐driven changes, and advances the functional ...
Jendrian Riedel +6 more
wiley +1 more source
Al-Khawarizmi Engineering Journal, 2012 An experimental study is carried out on the effect of vortex generators (Circular and square) on the flow and heat transfer at variable locations at (X = 0.5, 1.5, 2.5 cm) ahead of a heat exchanger with Reynolds number ranging from 62000< Re < 125000 and
Wisam Abed Kattea
doaj +2 more sources
Rheocasting versus Die Casting: An Insight into the Low‐Cycle Fatigue Behavior of AlSi7Mg0.6
Advanced Engineering Materials, EarlyView.The study compares rheocast lightweight components with high‐pressure die cast materials regarding microstructure and fatigue behavior. Rheocast process offers higher efficiency due to lower casting temperatures. Despite some microstructural differences, both processes show similar strengths (yield strength 125 MPa, tensile strength 240 MPa).
Julia Richter +4 more
wiley +1 more source
Jurnal Teknik ITS, 2014 Waste Heat Recovery merupakan instalasi yang digunakan untuk memanfaatkan kembali waste energy seperti exhaust gas. Penelitian dilakukan pada compact heat exchanger tipe louvered fin flat tube sebagai salah satu komponen penyusun waste heat recovery ...
Taqwim Ismail +1 more
doaj
Improvement of a Nusselt-Based Simulation Model for Heat Transfer in Rotary Heat Exchangers [PDF]
, 2020 Eloy Melian +2 more
openalex +1 more source
Advanced Engineering Materials, EarlyView.This article presents the NFDI‐MatWerk Ontology (MWO), a Basic Formal Ontology‐based framework for interoperable research data management in materials science and engineering (MSE). Covering consortium structures, research data management resources, services, and instruments, MWO enables semantic integration, Findable, Accessible, Interoperable, and ...
Hossein Beygi Nasrabadi +4 more
wiley +1 more source
Thermoelectric Modules Incorporating MgAgSb and Mg3(Sb,Bi)2 Synthesized Using a Melting Method
Advanced Engineering Materials, EarlyView.A scalable synthesis method for a thermoelectric material of MgAgSb is established. A thermoelectric power module of MgAgSb/Mg3(Sb,Bi)2 is fabricated, showing the conversion efficiency of 7.4% at ΔT = 315 K. The performance is comparable to conventional Bi2Te3 modules when they are operated with an air‐cooled heat exchanger.
Kazuo Nagase +8 more
wiley +1 more source
Feasibility Study of the Ø5 Tube-and-fin Heat Exchanger in Automotive Heat Pump System
Zhileng xuebao, 2013 The parallel flow microchannel (PFM) heat exchanger is widely used in automotive air conditioning system, but it has the disadvantage of easy-frost and difficult in water-drain in defrost .
Wei Wei +4 more
doaj
Advanced Engineering Materials, EarlyView.The work demonstrates that strategic wall‐thickness grading in diamond triply periodic minimal surface lattices enables precise tuning of deformation and failure behavior under compression. Different gradation patterns guide how and where the structure collapses, improving energy absorption or promoting controlled brittle failure.
Giovanni Rizza +3 more
wiley +1 more source
Heat Exchanger Reliability Analysis Based on Fouling Growth Model by Fault Tree Analysis
Chemical Engineering Transactions, 2019 The inherent reliability of heat exchanger in the design and manufacturing process, such as welding manner, yield strength, etc., has been the subject of many studies in the past. However, the operation reliability of heat exchanger, such as temperature,
Wu Xiao +5 more
doaj +1 more source