Results 71 to 80 of about 32,763 (264)

Numerical Investigation of the Heat Transfer Rate and Fluid Flow Characteristics of Conventional and Triply Periodic Minimal Surface (TPMS)-Based Heat Sinks

Engineering Proceedings
Heat sinks have been widely used in cooling systems due to their high heat transfer efficiency. In this study, the thermal performance and fluid flow characteristics of conventional and triply periodic minimal surfaces (TPMS)-based heat sinks were ...
Muhammad Usman Shahid, Muhammad Mahabat Khan, Muhammad Noman Shahid   +2 more
doaj   +1 more source

Thermal Conductivity Analysis and Investigation of an Aluminum-Graphene Composite Heat Sink [PDF]

Hangkong bingqi
To address the thermal dissipation challenges caused by high heat flux density in power modules under the high-performance and miniaturization trend of missile-borne electronic devices, this study proposes an innovative solution by optimizing the thermal
Li Hang, Shi Lanfang, Cai Ming
doaj   +1 more source

Single‐Atom Photocatalyst as Floatable Artificial Leaf for Upcycling Oceanic Plastic Waste

Advanced Materials, EarlyView.
To resolve the catastrophic disaster of oceanic plastic pollution, the novel Ru single atom loaded ZnIn2S4 photocatalysts, in the forms of powder or floatable artificial leaf, were prepared for direct conversion of raw polypropylene plastic into valuable chemicals. The optimized catalyst exhibits exceptional performance, with a total formic/acetic acid
Amin Talebian‐Kiakalaieh, Xin Xu, Wenzhong Ji, Yun Liu, Bingquan Xia, Jingrun Ran, Shi‐Zhang Qiao   +6 more
wiley   +1 more source

Scalable and Multifunctional PAN‐MXene Composite Fibers for Thermal Management, Photothermal Conversion, Energy Harvesting, and Sensing for Wearable Applications

Advanced Materials, EarlyView.
Electrospun PAN‐MXene nanofibers and yarns integrate enhanced thermal conductivity, photothermal conversion, and triboelectric energy harvesting within a flexible architecture. Interconnected MXene networks promote efficient phonon transport, while their surface chemistry strengthens tribo‐negative behavior, enabling a high power density of 432.7 mW m ...
Ahmadreza Moradi, Piotr K. Szewczyk, Urszula Stachewicz   +2 more
wiley   +1 more source

Heat Transfer Enhancement using Combined Microchannel with Vertical Rectangular Micro Fins

Nigerian Journal of Technological Development, 2023
This paper focuses on the numerical optimisation of a combined hybrid microchannel heat sink with rectangular solid fins. The axial length and volume are fixed, and external structure is allowed to vary. The simulation was performed on an elemental unit
N. Y. Godi
doaj  

Counterion‐Controlled Photocatalytic Doping of Organic Semiconductors

Advanced Materials, EarlyView.
Counterion size is shown to actively control photocatalytic doping in organic semiconductors. Small anions suppress aggregation of acridinium photocatalysts, enhance electron transfer, and dramatically increase doping efficiency. This simple strategy enables conductivities up to 2000 S cm−1 in benchmark polymers, revealing counterions as a powerful yet
Tiefeng Liu, Zesheng Liu, Ihor Sahalianov, Qiao He, Sang Young Jeong, Huotian Zhang, Qifan Li, Chi‐Yuan Yang, Junpeng Ji, Lize Bynens, Wouter Maes, Feng Gao, Han Young Woo, Martin Heeney, Glib Baryshnikov, Mats Fahlman, Simone Fabiano   +16 more
wiley   +1 more source

Honeybee cluster-not insulation but stressful heat sink. [PDF]

J R Soc Interface, 2023
Mitchell D.
europepmc   +1 more source

Phonon Engineering in Ultrathin Sn Films

Advanced Materials Interfaces, EarlyView.
When embedded in multilayer structures, ultrathin Sn layers demonstrate strongly modified vibrational density of states (VDOS). This allows engineering a drastic increase of the Lamb‐Mössbauer factor fLM$f_{\text{LM}}$ and thereby of the cross‐section for coherent excitation of the ultrasharp nuclear resonance of 119Sn$^{119}{\rm Sn}$. This enables the
Sven Velten, Kai Schlage, Ilya Sergeev, Olaf Leupold, René Steinbrügge, Varimalla Raghavendra Reddy, Michael Yu Hu, Esen Ercan Alp, Lars Bocklage, Ralf Röhlsberger   +9 more
wiley   +1 more source

Innovation Meets Accessibility in Melt Electrowriting 3D Printer Design: Continuous Process Monitoring and Automation via Modular Software and Hardware

Advanced Materials Technologies, EarlyView.
This manuscript describes the design and validation of an innovative melt electrowriting printer. With a turntable collector and modular software architecture, it unifies previous advanced MEW printer capabilities and enhances adaptability for a wide range of research applications.
Timo Baroth, Tim R. Dargaville, Paul D. Dalton, Dietmar W. Hutmacher   +3 more
wiley   +1 more source

Advances in Solid‐Phase Processing Techniques: Innovations, Applications, and Future Perspectives

Advanced Materials Technologies, EarlyView.
Based on practical manufacturing challenges, this review examines advanced solid‐phase processing techniques that overcome the inherent limitations of conventional melting‐based and traditional solid‐phase manufacturing, enabling the production of higher‐performance components at reduced cost through process innovation and improved supply‐chain ...
Tianhao Wang
wiley   +1 more source