Results 71 to 80 of about 6,842 (266)

Sheath-to-Ground Fault Impedance Calculation and Localization Method in Cross-Bonded High-Voltage Cable Systems

Energies
Abnormal circulating current induced by sheath grounding faults in cross-bonded high-voltage cables is a major cause of single-phase grounding faults.
Hang Wang, Bo Li, Liqiang Wang, Jing Tu, Shuai Yang, Jun Chen   +5 more
doaj   +1 more source

Tower-Footing Resistance and Lightning Trip-outs of 150 kV Transmission Lines in West Sumatra in Indonesia

MATEC Web of Conferences, 2018
The trip-out rates calculated by taking account of the reduction in the tower-footing resistance due to the ionizing effect agree well with the observed ones.
Warmi Yusreni, Michishita Koji
doaj   +1 more source

A TECHNIQUE OF MEASURING OF RESISTANCE OF A GROUNDING DEVICE

Electrical engineering & Electromechanics, 2016
Introduction. Measurement of resistance of the grounding device (GD) by means of a three-electrode system. This requires not only the right choice of installation locations of measuring electrodes, but also the determination of the point of zero ...
I.V. Nizhevskyi, V.I. Nizhevskyi
doaj   +1 more source

Enhanced Strength and Corrosion Resistance of Ti‐13Nb‐12Ta‐10Zr‐4Sn Alloy by Aging Treatment

Advanced Engineering Materials, EarlyView.
This work systematically investigates the effect of aging treatment on mechanical properties and corrosion behavior of vacuum arc‐melted Ti‐13Nb‐12Ta‐10Zr‐4Sn alloy. Owing to the increased α″ martensite, strength and corrosion resistance were significantly enhanced by aging treatment.
Yuhua Li, Rong Zhao, Qian Zhang, Haojie Wang, Yujing Liu, Lai‐Chang Zhang   +5 more
wiley   +1 more source

Stator grounding fault severity characterization and novel inverse-time protection method for large generators

International Journal of Electrical Power & Energy Systems
The existing injection-type stator grounding protection schemes for large generators are configured to issue only an alarm signal under high transition resistance grounding fault conditions. Thus, the fault cannot be promptly cleared.
Yikai Wang, Jie Ou, Jian Qiao, Zengping Wang, Xianggen Yin, Chunguang Ren   +5 more
doaj   +1 more source

Evaluation of Plasticity and Creep Parameters From Tensile Stress–Strain Data for a Range of Strain Rates

Advanced Engineering Materials, EarlyView.
This plot compares experimental tensile stress–strain curves (with 4 different strain rates) and corresponding modelled curves (obtained using the optimised sets of Voce and Miller–Norton parameter values shown). The inferred M‐N values, characterizing the creep, are very similar to those obtained via conventional creep testing.
S. Ooi, R. P. Thompson, T. W. Clyne
wiley   +1 more source

Direct Metal Deposition of Graphene–Ti28Nb35.4Zr Matrix Composites With Enhanced Mechanical, Corrosion, and Biocompatibility Properties for Bone Implants

Advanced Engineering Materials, EarlyView.
Graphene nanoplatelet (0.1 wt.%) reinforcement significantly enhances the performance of β Ti‐28Nb‐35.4Zr alloy. Grain refinement, reduced water contact angle, and improved surface characteristics promote osteoblast adhesion and complete surface coverage after 7 days.
Khurram Munir, Jixing Lin, Yuncang Li, Li Zhu, Paul F. A. Wright, Cuie Wen   +5 more
wiley   +1 more source

Toward Knowledge‐Based Workflows: A Semantic Approach to Atomistic Simulations for Mechanical and Thermodynamic Properties

Advanced Engineering Materials, EarlyView.
Knowledge‐based atomistic workflows are presented for mechanical and thermodynamic properties. By coupling modular simulations with ontology‐aligned metadata and provenance, Fe case studies on elastic behavior, defects, thermal properties, and Hall–Petch strengthening reveal how FAIR, queryable, and reusable simulation data can be generated. Mechanical
Abril Azócar Guzmán, Hoang‐Thien Luu, Sarath Menon, Tilmann Hickel, Nina Merkert, Stefan Sandfeld   +5 more
wiley   +1 more source

A Modified Ampacity Calculation Method for High-Voltage Cables Considering Grounding Modes

Applied Sciences
To address the limitation of the IEC 60287 standard in accurately representing the electrothermal characteristics of cables under different grounding conditions, this study proposes a modified equivalent thermal resistance method, using a YJLW03-Z 64/110
Qianqiu Shao, Songhai Fan, Zongxi Zhang, Fenglian Liu, Jinkui Lu, Zhengzheng Fu, Pinlei Lv   +6 more
doaj   +1 more source

Electrochemical Behavior of Flame‐Sprayed Sc‐Doped AlCoCrFeMo High‐Entropy Alloy Coatings in 3.5% Sodium Chloride Solution

Advanced Engineering Materials, EarlyView.
Scandium (Sc)‐doped AlCoCrFeMo HEA coatings are fabricated via flame spraying with 0.1, 0.3, and 0.5 wt% Sc additions. Among these, the HEA‐Sc0.3 coating exhibits the highest corrosion resistance, indicated by a more positive corrosion potential and lower current density.
Pankaj Kumar, Akash Vyas, Mohammad Aatif Qazi, Nashit Jalal, Maria Ophelia Jarligo, Mostafa Yakout, Jing Liu, André McDonald   +7 more
wiley   +1 more source