Results 61 to 70 of about 311,341 (350)

High Temperature Oxidation and Corrosion Properties of High Entropy Superalloys

Entropy, 2016
The present work investigates the high temperature oxidation and corrosion behaviour of high entropy superalloys (HESA). A high content of various solutes in HESA leads to formation of complex oxides, however the Cr and Al activities of HESA are ...
Te-Kang Tsao, An-Chou Yeh, Chen-Ming Kuo, Hideyuki Murakami   +3 more
doaj   +1 more source

The effects of carboxylic acids in aluminum anodizing [PDF]

, 2017
Hard-anodized alumina coatings were formed in sulfuric acid at low temperature and high current density in the presence of carboxylic acid additives. Citric acid, trimesic acid, mellitic acid and ethylenediaminetetraacetic acid (EDTA) were utilized in ...
Koczera, Abby E
core   +1 more source

Phenomenological and Physically Based Modeling of Flow Stress and Strengthening Mechanism of Inconel 718

Advanced Engineering Materials, EarlyView.
Nickel‐based alloys are widely used in high‐temperature applications due to their excellent mechanical strength and oxidation resistance. However, properties such as high‐temperature strength and pronounced work‐hardening make them difficult to machine.
Soheil Rooein, Oliver Schenk, Christoph Broeckmann   +2 more
wiley   +1 more source

Effect of Laser Deoxidation on Adhesive‐Bonded Aluminum in an Oxygen‐Free Atmosphere

Advanced Engineering Materials, EarlyView.
This study investigates laser ablation of aluminum under oxygen‐free conditions. The goal is to produce oxide‐free substrates that enable improved adhesive bonding with epoxy. Optimized laser parameters (90% overlap, 300 µJ) combined with oxide‐free substrates result in the highest tensile strength of the adhesive bond.
Sandra Gerland, Finn‐Lennard Janthur, Sarah Seffer, Jörg Hermsdorf, Ludger Overmeyer, Annika Raatz   +5 more
wiley   +1 more source

Novel Tailoring of Ternary ZnS‐MXene‐TiO2 Nanocomposite Heterojunction and Its Tunable Electrochemical Properties With Enhanced Photocatalytic Degradation

Advanced Engineering Materials, EarlyView.
ZnS‐MXene‐TiO2 nanocomposite heterojunction for photocatalytic decomposition of this methylene blue dye (MB) greatly improves light absorption, charge separation, and active site area. Two‐dimensional MXene forms nanocomposites by easily combining them with 0D (quantum dots), 1D (tube and wire), 2D (plane and sheet), and 3D (particle and lamellar ...
Latiful Kabir, Dohyun Kim, Minho Song, Jae Doc Na, Young Jun Joo, Kwang Youn Cho, Karna Wijaya, Won‐Chun Oh   +7 more
wiley   +1 more source

Investigation into high-temperature corrosion in a large-scale municipal waste-to-energy plant

, 2010
High-temperature corrosion in the superheater of a large-scale waste-to-energy plant was investigated. A comparison of nickel-/iron-based alloys and austenitic stainless steel probes placed in the furnace demonstrated that temperature and particle ...
Finney, K.N., Leyland, A., Phongphiphat, A., Ryu, C., Sharifi, V.N., Swithenbank, J., Yang, Y.B.   +6 more
core   +1 more source

The significance of velocity exponents in identifying erosion-corrosion mechanisms [PDF]

, 1993
The modes of erosion-corrosion are diverse and may vary from being ''erosion-dominated'', where erosion of metal is the dominant process, to ''corrosion-dominated'', where erosion of oxide scale is the dominant process.
Stack, Margaret, Stott, F.H., Wood, G.C.
core   +3 more sources

Removing Oxide Layers and Retaining Oxide‐Free Steel Surfaces by Polishing in Oxygen‐Free Atmosphere

Advanced Engineering Materials, EarlyView.
In this study, the efficacy of wet mechanical polishing under an oxygen‐free atmosphere for deoxidation and the retention of an oxide‐free steel surface are elucidated using X‐ray photoelectron spectroscopy. The methodology proved successful; however, the results were highly dependent on the preparation of the solvents used to clean the samples after ...
Friedrich Bürger, Lienhard Wegewitz, Wolfgang Maus‐Friedrichs   +2 more
wiley   +1 more source

Predicting the steady state thickness of passive films in order to prevent degradations of implant [PDF]

, 2013
Some implants have approximately a lifetime of 15 years. The femoral stem, for example, should be made of 316L/316LN stainless steel. Fretting corrosion, friction under small displacements, should occur during human gait, due to repeated loadings and un ...
Geringer, Jean, Macdonald, Digby D., Taylor, Mathew L.   +2 more
core   +2 more sources

Influence of an Oxygen‐Free Atmosphere on Diamond‐Single‐Grain Scratching of Ti–6Al–4V

Advanced Engineering Materials, EarlyView.
Single‐grain scratching of Ti–6Al–4V is investigated under controlled, oxygen‐free, and ambient atmospheres using a novel experimental setup with in situ high‐speed imaging. The approach enables direct observation of chip formation and adhesion under suppressed oxidation.
Berend Denkena, Benjamin Bergmann, Michael Zenger   +2 more
wiley   +1 more source