Results 31 to 40 of about 5,080 (220)

Impact of Multi-Physics HiL Test Benches on Wind Turbine Certification

open access: yesEnergies, 2022
Recently developed nacelle test benches for wind turbines, equipped with multi-physics Hardware-in-the-Loop (HiL) systems, enable advanced testing and even certification of next-generation wind turbines according to IEC61400-21.
Lennard Kaven   +7 more
doaj   +1 more source

Co-simulation perspective on evaluating the simulation with the engine test bench in the loop

open access: yesAutomatika, 2022
This article shows how a hardware in the loop (HIL) simulation can be formulated in such a way that the quality of the simulation can be assessed by evaluating the total energy residual (TER).
Slaven Glumac   +3 more
doaj   +1 more source

Design and Implementation of a Hardware-in-the-Loop Simulation System for a Tilt Trirotor UAV

open access: yesJournal of Advanced Transportation, 2020
The tilt trirotor unmanned aerial vehicle (UAV) is a novel aircraft that has broad application prospects in transportation. However, the development progress of the aircraft is slow due to the complicated control system and the high cost of the flight ...
Li Yu   +4 more
doaj   +1 more source

An ADRC-Based Hardware-in-the-Loop System for Maximum Power Point Tracking of a Wind Power Generation System

open access: yesIEEE Access, 2020
To improve the efficiency of the wind power generation, this article proposes an active disturbance rejection controller (ADRC) based MPPT strategy, and establishes a LabVIEW FPGA platform based hardware-in-the-loop (HIL) test system.
Aihua Wu, Jing-Feng Mao, Xudong Zhang
doaj   +1 more source

Hardware in the loop simulation test platform of fuel cell backup system

open access: yesMATEC Web of Conferences, 2015
Based on an analysis of voltage mechanistic model, a real-time simulation model of the proton exchange membrane (PEM) fuel cell backup system is developed, and verified by the measurable experiment data. The method of online parameters identification for
Ma Tiancai   +5 more
doaj   +1 more source

Low-Cost Hardware-in-the-Loop Platform for Embedded Control Strategies Simulation

open access: yesIEEE Access, 2019
The increasing need for testing and prototyping designs under more realistic conditions is responsible for the advancement of new types of simulation. In this scenario, one type of simulation which has gained high notoriety and applicability is the one ...
Alceu Bernardes Castanheira De Farias   +4 more
doaj   +1 more source

Design and Implementation of Integrated Virtual Sensor Simulator Unit for Hardware in the Loop Laboratory of Autonomous Underwater Vehicle [PDF]

open access: yesمجله مدل سازی در مهندسی
Evaluating performance of the integrated system and its subsystems of the Autonomous Underwater Vehicle (AUV), such as sensors and actuators, requires the maybe expensive hardware in the loop laboratory (HIL).
Gholamreza Nadalinia Chare   +2 more
doaj   +1 more source

Hardware-in-the-Loop Techniques for Complex Systems Analysis: Bibliometric Analysis of Available Literature

open access: yesApplied Sciences, 2023
Simulating complex systems in real time presents both significant advantages and challenges. Hardware-in-the-loop (HIL) simulation has emerged as an interesting technique for addressing these challenges.
Luisa F. Cabeza   +2 more
doaj   +1 more source

Optimization of B Cell Responses in Human Immune System Mice Through Organoid Based Screening

open access: yesAdvanced Science, EarlyView.
Human immune system (HIS) mice show limited B cell responses to immunization. Using HIS mouse spleen organoids, this study identifies cytokine combinations and innate immune signals that drive human B cell expansion, differentiation, and class‐switch. Applying these signals in vivo through temporal separation enables antigen‐specific IgG responses and ...
Haiqiao Sun   +6 more
wiley   +1 more source

Five-Axis Machine Tool Condition Monitoring Using dSPACE Real-Time System

open access: yes, 2012
This paper presents the design, development and SIMULINK implementation of the lumped parameter model of C-axis drive from GEISS five-axis CNC machine tool.
Longstaff, Andrew P.   +7 more
core   +1 more source

Home - About - Disclaimer - Privacy