Results 31 to 40 of about 4,035,475 (305)
Summary of investigations conducted in 1967 : Woods Hole Oceanographic Institution Woods Hole, Massachusetts [PDF]
This collection of brief "summaries of investigations" has been prepared by the members of the research staff of the Woods Hole Oceanographic Institution and this volume is a continuation of our early traditions.
Woods Hole Oceanographic Institution, /
core +1 more source
Investigation of the Effect of Band Offset and Mobility of Organic/Inorganic HTM Layers on the Performance of Perovskite Solar Cells [PDF]
: Perovskite solar cells have become an attractive subject in the solar energydevice area. During ten years of development, the energy conversion efficiency has beenimproved from 2.2% to more than 22%, and it still has a very good potential for ...
davood jalalian +2 more
doaj
Stable decaphenylcyclopentasilane (DPPS) hole transport layers were developed for guanidinium-, formamidinium-, or ethylammonium-added double-stacked CH3NH3PbI3 perovskite photovoltaic devices without using 2,2′,7,7′-tetrakis (N,N-di-p-methoxyphenylamino)
Iori Ono +8 more
doaj +1 more source
A Hybrid Hole Transport Layer for Perovskite-Based Solar Cells
This paper presents the effect of a composite poly(3,4-ethylenedioxythiophene) polystyrene sulfonate PEDOT:PSS and copper-doped nickel oxide (Cu:NiOx) hole transport layer (HTL) on the performance of perovskite solar cells (PSCs).
Joseph Asare +6 more
doaj +1 more source
In this work, a MAPbBr3 quantum dot (QD-MAPbBr3) layer was prepared by a simple and rapid method. Octylammonium bromide (OABr) gives the MAPbBr3 better exciton binding energy, good surface morphology, and stability. To form a nanocrystalline thin film on
Lung-Chien Chen +4 more
doaj +1 more source
Recent research shows that the interface state in perovskite solar cells is the main factor which affects the stability and performance of the device, and interface engineering including strain engineering is an effective method to solve this issue.
Bingjuan Zhang +8 more
doaj +1 more source
In this paper, a blue fluorescent organic light-emitting diode (OLED) with a 1 cm2 emitting area was fabricated by a solution process. The ITO/spin MADN:13% UBD-07/TPBi/Al was used as the basic structure in which to add a hole-injection layer PEDOT:PSS ...
Kuo-Chun Huang +4 more
doaj +1 more source
Mycobacterial 3‐methylcrotonyl‐CoA carboxylase uses a mobile biotin‐carrying domain to shuttle a carboxyl group between two catalytic sites, enabling carboxylation of 3‐methylcrotonyl‐CoA during leucine breakdown. Cryo‐electron microscopy captures the carrier at both sites and reveals an inward loop movement that may prevent futile rebinding to the ...
Ajit Yadav +2 more
wiley +1 more source
Hole dangling-bond capture cross-sections in a-Si:H [PDF]
It is demonstrated that the occupation statistics for a Gaussian distribution of dangling bond states may account for the measured variation of hole mobility-lifetime values in hydrogenated amorphous silicon as the Fermi energy is systematically varied ...
Goldie, David M.
core +1 more source
Interfacial carrier transfer kinetics is critical to the efficiency and stability of perovskite solar cells. Herein, we measure the regeneration rate constant, absorption cross-section, reduction rate constant, and conductivity of hole transport layered ...
Getachew Alemu Anshebo +3 more
doaj +1 more source

