Gong-kuang zidonghua, 2013 The paper introduced research development and actual application status of automation control technology for fully mechanized working face at home and abroad, indicated development tendency of automation control technology for fully mechanized working ...
HUANG Zeng-hua
doaj +1 more source
Microstructure Evolution of a VMnFeCoNi High‐Entropy Alloy After Synthesis, Swaging, and Annealing
Advanced Engineering Materials, EarlyView.The synthesis and processing (rotary swaging and annealing) of the novel VMnFeCoNi alloy is investigated, alongside the estimation of the grain size effect on hardness. Analysis of a wide grain size range of recrystallized microstructures (12–210 µm) reveals a low annealing twin density.
Aditya Srinivasan Tirunilai +6 more
wiley +1 more source
Conscious design and new technologies for the optimization of therapeutic space
Techne, 2015 The project Casa pre-dimissioni is aimed at facilitating the recovery of the daily life by whom suffers of disability, adapting domestic spaces to the specific needs of use.
Marzia Morena
doaj +1 more source
Improvements of the xAAL Home Automation System
Future Internet, 2020 The xAAL home automation system has been designed on the basis of distributed systems principles with messages passing and home network communications over IP.
Christophe Lohr, Jérôme Kerdreux
doaj +1 more source
Home Automation Management with WLAN (802.11g) and RF Remote Control [PDF]
Al-Rafidain Journal of Computer Sciences and Mathematics, 2009 The home automation becomes important, because it gives the user the comfort and ease for using the home devices. The implementation and design of wireless home automation control use two methods, WLAN technology and RF remote control handheld to control
Mahmood Majeed +2 more
doaj +1 more source
Remote control of devices using an 8-bit embedded XML & dynamic web-server in a SmartHouse environment : a thesis presented in partial fulfilment of the requirements for the degree of Master of Engineering in Computer Systems Engineering at Massey University [PDF]
, 2006 This paper focuses on an Embedded System known as "TCP/IC" and its role in the "house of the future" - the SmartHouse. Overall, the aim of the TCP/IC was to design a device which could interact with a user (or AI control system) and allow for the control
Kok, Albert Leon
core
Home Energy Consumption Feedback: A User Survey [PDF]
, 2012 Buildings account for a relevant fraction of the energy consumed by a country, up to 20-40% of the yearly energy consumption. If only electricity is considered, the fraction is even bigger, reaching around 73% of the total electricity consumption ...
Bonino, Dario +2 more
core +1 more source
An Experimental High‐Throughput Approach for the Screening of Hard Magnet Materials
Advanced Engineering Materials, EarlyView.An entire workflow for the high‐throughput characterization and analysis of compositionally graded magnetic films is presented. Characterization protocols, data management tools and data analysis approaches are illustrated with test case Sm(Fe, V)12 based films.
William Rigaut +16 more
wiley +1 more source
Multiphysics-Coupled Load-Bearing Capacity of Piezoelectric Stacks in Low-Temperature Environments
SensorsUnder low-temperature conditions, the load-bearing capacity of piezoelectric stacks arises from coupled thermo-electro-mechanical interactions, with temperature fluctuations, compressive prestress, and excitation voltage critically modulating performance.
Yang Li +8 more
doaj +1 more source
3D‐Printed Sulfur‐Derived Polymers With Controlled Architectures for Lithium‐Sulfur Batteries
Advanced Functional Materials, EarlyView.Rheology‐guided formulation design for direct ink writing enables the fabrication of 3D sulfur copolymer cathodes with controlled architectures for lithium‐sulfur batteries. The printed electrodes exhibit multiscale porosity and high sulfur utilization, delivering enhanced electrochemical performance compared to conventional cast electrodes.
Bin Ling +7 more
wiley +1 more source