Microstructural and mechanical characterisation of 7075 aluminium alloy consolidated from a premixed powder by cold compaction and hot extrusion [PDF]
, 2014 The present work concerns the processing of 7075 Al alloy by cold compaction and hot extrusion of a pre-mixed powder. To this end, a premixed Al-Zn-Mg-Cu powder, Alumix 431D, was uniaxially cold pressed at 600 MPa into cylindrical compacts 25 mm in ...
Jabbari Taleghani, Mohammad Ali +2 more
core +2 more sources
Hot Melt Extrusion Processing Parameters Optimization [PDF]
Processes, 2020 The aim of this study was to demonstrate the impact of processing parameters of the hot-melt extrusion (HME) on the pharmaceutical formulation properties. Carbamazepine (CBZ) was selected as a model water-insoluble drug. It was incorporated into Soluplus®, which was used as the polymeric carrier, to produce a solid dispersion model system.
Abdullah Alshetaili +3 more
openaire +1 more source
Results in Physics, 2019 Magnesium matrix composites reinforced with short carbon fiber (SCF) (SCF/AZ31B composites) were fabricated by multi-times hot-extrusion with mass fraction of 3%. The effect of extrusion times and addition of SCFs on microstructure, mechanical properties
Zhao Yang +4 more
doaj +1 more source
Recent development, challenges, and prospects of extrusion technology
Future Foods, 2021 There is a significant advancement in the modification of extruders for the commercial application in food processing sector, especially during the last three decades.
Krishna Prabha +6 more
doaj +1 more source
Flow stress and hot deformation activation energy of 6082 aluminium alloy influenced by initial structural state [PDF]
, 2019 Stress-strain curves of the EN AW 6082 aluminium alloy with 1.2 Si-0.51 Mg-0.75 Mn (wt.%) were determined by the uniaxial compression tests at temperatures of 450-550 degrees C with a strain rate of 0.5-10 s(-1).
Kawulok, Petr +5 more
core +1 more source
Investigation of Hot-extrusion Effect on Microhardness, Microstructure and Corrosion Behavior of Magnesium-based Bio-composites [PDF]
Journal of Stress Analysis, 2019 Magnesium alloys are a unique choicefor orthopedic implants due to their biocompatibility and biodegradability properties. In this article, the impact of hot-extrusion process is investigated on microhardness, microstructure, and corrosion behavior of ...
E. Ghazizadeh +2 more
doaj +1 more source
Solid state recycling of used aluminum alloy beverage cans by thermomechanical consolidation
Heat Treatment and Surface Engineering, 2022 Solid-state recycling of used aluminum alloy beverage cans was accomplished by thermomechanical consolidation of the sheet fragments produced by shredding the cans.
Ziyi Wang +7 more
doaj +1 more source
Effect of frictional boundary conditions and percentage area reduction on the extrusion pressure of Aluminum AA6063 alloy using FE analysis modelling [PDF]
, 2020 © 2020 by the authors; licensee Growing Science, Canada. This is an open access article distributed under the terms and conditions of the Creative Commons Attribution (CC-BY) license (http://creativecommons.org/licenses/by/4.0/).Finite Element Analysis ...
Ismail, Sikiru O. +2 more
core +2 more sources
Journal of Materials Research and Technology, 2022 The MgZn1.2Zr0.35 (wt%) alloys for orthopedic applications enhanced by small amount addition of zirconium and subsequent hot extrusion working based on cast MgZn1.2 system were successfully fabricated.
Jun Fan +8 more
doaj +1 more source
Hot-Melt Extrusion: from Theory to Application in Pharmaceutical Formulation—Where Are We Now?
AAPS PharmSciTechHot-melt extrusion (HME) is a globally recognized, robust, effective technology that enhances the bioavailability of poorly soluble active pharmaceutical ingredients and offers an efficient continuous manufacturing process.
H. Patil +9 more
semanticscholar +1 more source