Results 141 to 150 of about 85,220 (297)
Advanced Materials Interfaces, EarlyView.Large size (∼100 µm) monolayer MoS2 grown by LPI‐CVD on n‐GaN exhibit a high n‐type doping, very low strain, and a type‐I band alignment at MoS2/GaN interface. Photocurrent measurements under illumination with photon energies from ∼2 to ∼5 eV show superior electro‐optical performances of these MoS2/n‐GaN heterojunctions as compared to Ni/n‐GaN devices ...
Salvatore Ethan Panasci +12 more
wiley +1 more source
Advanced Materials Interfaces, EarlyView.Low‐temperature passivation of SiC reveals that optical surface quality and chemical stability are not directly correlated. Ar plasma‐treated and SiNx‐passivated surfaces yield the lowest photoluminescence background, whereas CF4 plasma and ALD‐grown dielectrics introduce higher emission.
Marina Scharin‐Mehlmann +4 more
wiley +1 more source
Automotive VHDL-AMS Electro-mechanics Simulations [PDF]
, 2011 Mariagrazia Graziano, Massimo Ruo Roch
core +2 more sources
Advances in Halide Perovskites for Photon Radiation Detectors
Advanced Materials Technologies, EarlyView.This work highlights recent progress in perovskite‐based photon radiation detectors, covering organic–inorganic hybrid, inorganic, lead‐free double, and vacancy‐ordered halide perovskites. Their detection performance is compared, material‐specific advantages and challenges are examined, and provides insight into current limitations and future ...
Liangling Wang +3 more
wiley +1 more source
Hydrogel‐Based 3D‐Printable Stretchable Pressure Sensor
Advanced Materials Technologies, EarlyView.We present a carbon‐black‐functionalized double‐network granular hydrogel (DNGH) pressure sensor capable of detecting pressures from 200 Pa, equivalent to a light finger touch, up to 500 kPa. The sensor exhibits signal drifts below 3.5% after 800 cycles and response times around 80 ms. Leveraging this broad sensing range, we 3D print this material into
Tianyu Yuan +4 more
wiley +1 more source
3D Printed Multimaterial Microfluidic Transistors
Advanced Materials Technologies, EarlyView.We introduce a biocompatible, high resolution photopolymer resin that closely mimics the Young's Modulus (elasticity) and reversible stretchability (no hysteresis) of poly(dimethylsiloxane) (PDMS), enabling the fabrication of microfluidic transistors (i.e., microvalves capable of proportional amplification) by multimaterial stereolithography (mSLA ...
Alireza Ahmadianyazdi +7 more
wiley +1 more source
Exploring the Potential of Microwave Annealing for Enhancing Si‐based GeSn Lasers
Advanced Materials Technologies, EarlyView.We explore low‐thermal‐budget microwave annealing to enhance the performance of group‐IV GeSn lasers on Si. Microwave annealing under optimal conditions can simultaneously relax unwanted compressive strain and enhance the material quality of the GeSn active layer, thereby reducing the threshold and increasing the laser operating temperature.
Yue‐Tong Jheng +8 more
wiley +1 more source
Advanced Materials Technologies, EarlyView.Parallel wiring of bioelectrochemical devices with conventional generators unexpectedly boosts output. A biophotovoltaic paired with a solar cell delivers up to 50% more power at low loads than their separate contributions; a plant microbial fuel cell shows similar current gains.
Valeria Marsaglia +4 more
wiley +1 more source
Vat Polymerization 3D Printing for Controlled Drug Release Applications
Advanced Materials Technologies, EarlyView.ABSTRACT Vat polymerization (VP) 3D printing, a light‐based additive manufacturing technique, has emerged as a promising technique for fabricating complex drug delivery systems with high precision and spatial resolution. This layer‐by‐layer manufacturing process enables the creation of intricate geometries and customizable architectures, which are ...
Hafiz Busari +2 more
wiley +1 more source
Two-boosting-staged single-switched ultrahigh step-up topology with continuous input current and reduced voltage stress. [PDF]
Sci RepShayeghi H +4 more
europepmc +1 more source