Results 91 to 100 of about 17,605 (305)

Electrochemical Evaluation of Compressed Selective Laser Melted AlSi7Mg and AlSi10Mg Alloys in Chloride Environment

open access: yesAdvanced Engineering Materials, EarlyView.
The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin   +2 more
wiley   +1 more source

Effective Young’s modulus of biopolymer composites with imperfect interface

open access: yes, 2010
The effective elastic behaviour of a biopolymer composite with random microstructure is studied. The effective elasticity modulus is computed as function of the protein fraction with the hypothesis of an imperfect interface.
S. Guessasma   +7 more
core   +1 more source

Innovative Processing of Compacted Waste Aluminum Alloy Powders via Controlled Remelting and Solidification

open access: yesAdvanced Engineering Materials, EarlyView.
This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira   +4 more
wiley   +1 more source

Microstructural Evolution and Vacancy Defect Formation in Mn–Mo–Ni RPV Steel Under Low Cycle Fatigue: Insights From EBSD and PALS

open access: yesAdvanced Engineering Materials, EarlyView.
Low‐cycle fatigue damage in Mn–Mo–Ni reactor pressure vessel steel is examined using a combined electron backscatter diffraction and positron annihilation lifetime spectroscopy approach. The study correlates texture evolution, dislocation substructure development, and vacancy‐type defect formation across uniform, necked, and fracture regions, providing
Apu Sarkar   +2 more
wiley   +1 more source

Analysis of imperfect interfaces in cobalt ferrite plates using a linear spring model: a comparative study with terfenol-D

open access: yesDiscover Materials
Purpose This research aims to explore the transmission of seismic surface waves through a two magneto-strictive materials i.e. cobalt ferrite and Terfenol-D when embedded in a plate-substrate configuration with non-ideal interface.
Seema, Abhinav Singhal
doaj   +1 more source

Scaled behavior of interface waves at an imperfect solid-solid interface

open access: yes, 2012
International audienceLaser ultrasonic techniques allow the remote analysis of adhesion mechanisms at imperfect interfaces up to GHz frequencies. However, the sensitivity of interface waves to the properties of the contact is not very well known.
Tony Valier-Brasier   +5 more
core   +1 more source

Dynamic magneto-viscoelastic model for magnetorheological nanocomposites with imperfect interface [PDF]

open access: yes, 2019
A dynamic magneto-viscoelastic interface model is proposed to study the effective magneto-mechanical responses of magnetorheological nanocomposites filled with carbon nanotubes.
Sun, LZ, Chen, Xiangrong, Li, Rui
core   +1 more source

Thermodynamic Pathways of Nonequilibrium Solidification in Wire‐Arc Additive Manufacturing Fe‐Based Multicomponent Alloy Structures

open access: yesAdvanced Engineering Materials, EarlyView.
Geometry‐driven thermal behavior in wire‐arc additive manufacturing (WAAM) influences microstructural evolution during nonequilibrium solidification of a chemically complex Fe–Cr–Nb–W–Mo–C nanocomposite system. By comparing different deposits configurations, distinct entropy–cooling rate correlations, segregation, and carbide evolution are revealed ...
Blanca Palacios   +5 more
wiley   +1 more source

Home - About - Disclaimer - Privacy