Results 61 to 70 of about 75,619 (293)

Enhancing Corrosion Resistance and Mechanical Strength of 3D‐Printed Iron Polylactic Acid for Marine Applications via Laser Surface Texturing

Advanced Engineering Materials, EarlyView.
Laser surface texturing significantly improves the corrosion resistance and mechanical strength of 3D‐printed iron polylactic acid (Ir‐PLA) for marine applications. Optimal laser parameters reduce corrosion by 80% and enhance tensile strength by 25% and ductility by 15%.
Mohammad Rezayat, Mojtaba Karamimoghadam, Mohammadreza Lalegani Dezaki, Ali Zolfagharian, Giuseppe Casalino, Antonio Mateo, Mahdi Bodaghi   +6 more
wiley   +1 more source

Analytical modeling of surface roughness in precision grinding of particle reinforced metal matrix composites considering nanomechanical response of material [PDF]

, 2019
Grinding is usually applied for particle reinforced metal matrix composites (PRMMCs) to achieve high ground surface quality. However, the surface quality especially surface roughness is difficult to predict theoretically due to different mechanical ...
Cai, Rui, Huang, Chuanzhen, Wang, Jun, Yao, Peng, Zhang, Zhenzhong, Zhu, Hongtao   +5 more
core   +1 more source

Dynamic Precipitation during High‐Pressure Torsion of a Magnesium–Manganese Alloy

Advanced Engineering Materials, EarlyView.
An ultrafine‐grained alloy is produced by high‐pressure torsion of solutionized Mg–1.35 wt% Mn. Precipitation of nanometer‐scale Mn particles during deformation provides pinning sites. This prevents the formation of a bimodal grain structure and results in a finer grain size than for pure Mg.
Julian M. Rosalie, Anton Hohenwarter
wiley   +1 more source

Development and Preliminary In Vivo Study of 3D‐Printed Bioactive Glass Scaffolds with Trabecular Architecture

Advanced Engineering Materials, EarlyView.
This study reports the fabrication of trabecular bioactive glass scaffolds (composition “1d”: 46.1SiO2‐28.7CaO‐8.8MgO‐6.2P2O5‐5.7CaF2‐4.5Na2O wt%) through vat photopolymerization and the relevant results from mechanical testing and in vivo implantation procedures in rabbit femora, showing great promise for bone tissue engineering applications.
Dilshat Tulyaganov, Roberta Gabrieli, Avzal Akbarov, Nigora Nigmatova, Bekhzod Khabilov, Alessandro Schiavi, Martin Schwentenwein, Enrica Verné, Francesco Baino   +8 more
wiley   +1 more source

Effects of Carbon Nanoparticles on Triboelectro‐Induced Surface Defects

Advanced Engineering Materials, EarlyView.
Carbon nanoparticles added to grease modify the electrocontact behavior. The synergy of particle concentration and electric current dominates the surface damage of metals in contact. Electrical surface damage caused by current leakage is a critical challenge in high‐performance applications such as electric vehicle (EV) drivetrains and wind turbine ...
Mohsen Tajedini, Lu Fang, Jacob Bons, Mohammad Humaun Kabir, Evan Johnson, Joe Kosmoski, Hong Liang   +6 more
wiley   +1 more source

Effect of annealing ambient conditions on crack formation mechanisms of bulk Bi-2212 ceramic systems

Journal of Asian Ceramic Societies, 2021
This study paves way to examine the influence of different annealing conditions (temperature range of 830-850°C and duration intervals 24-48 h) on the fundamental mechanical performance and characteristic quantities of polycrystalline Bi2.1Sr2.0Ca1.1Cu2 ...
U. Erdem, B. Akkurt, A.T. Ulgen, Y. Zalaoglu, T. Turgay, G. Yildirim   +5 more
doaj   +1 more source

A method for measuring the contact area in instrumented indentation testing by tip scanning probe microscopy imaging [PDF]

, 2014
The determination of the contact area is a key step to derive mechanical properties such as hardness or an elastic modulus by instrumented indentation testing. Two families of procedures are dedicated to extracting this area: on the one hand, post mortem
Charleux, L., Guin, J. -P., Keryvin, V., Nivard, M., Sanglebœuf, J. -C., Yokoyama, Y.   +5 more
core   +5 more sources

Hybrid Auxetic Architectures: Integrating Curvature‐Driven Design for Enhanced Mechanical Tunability and Structural Performance

Advanced Engineering Materials, EarlyView.
Curvature‐tuned auxetic lattices are designed, fabricated, and mechanically characterized to reveal how geometric curvature governs stretchability, stress redistribution, and Poisson's ratio evolution. Photoelastic experiments visualize stress pathways, while hyperelastic simulations quantify deformation mechanics.
Shuvodeep De, Giovanni Meli, Meysam Khalighian, Anahita Emami   +3 more
wiley   +1 more source

Mechanical Properties of Microstructural Components of Inorganic Materials [PDF]

, 2013
Disertační práce se zabývá studiem strukturních a mechanických vlastností anorganických materiálů. Cílem je nalezení jednotlivých fází ve zkoumaném materiálu a hlavně lokalizace (mechanicky) nejslabšího místa, jeho ovlivnění a následně výroba materiálu o
Wasserbauer, Jaromír
core  

Failure analysis of CFRP laminates subjected to Compression After Impact: FE simulation using discrete interface elements [PDF]

, 2013
This paper presents a model for the numerical simulation of impact damage, permanent indentation and compression after impact (CAI) in CFRP laminates.
Bouvet, Christophe, Hongkarnjanakul, Natthawat, Rivallant, Samuel   +2 more
core   +3 more sources