Results 221 to 230 of about 2,959,763 (291)

What Do Large Language Models Know About Materials?

Advanced Engineering Materials, EarlyView.
If large language models (LLMs) are to be used inside the material discovery and engineering process, they must be benchmarked for the accurateness of intrinsic material knowledge. The current work introduces 1) a reasoning process through the processing–structure–property–performance chain and 2) a tool for benchmarking knowledge of LLMs concerning ...
Adrian Ehrenhofer, Thomas Wallmersperger, Gianaurelio Cuniberti   +2 more
wiley   +1 more source

Batch Process Design Including Initial and Operating Conditions and Online Property Estimation in Acrylic Resin Polymerization

ACS Omega
Rinta Kawagoe, Fumiya Hamada, Kazutoshi Terauchi, Toshinori Yamaji, Hiromasa Kaneko   +4 more
doaj   +1 more source

Energy-structure coupling mechanism and damage evolution model of red sandstone during soaking-softening process. [PDF]

PLoS One
Zhang J, Liang N.
europepmc   +1 more source

On the Lightweight Potential of Laser Additive Manufactured NiTi Triply Periodic Minimal Sheet Lattices

Advanced Engineering Materials, EarlyView.
This study explores the lightweight potential of laser additive‐manufactured NiTi triply periodic minimal surface sheet lattices. It systematically investigates the effects of relative density and unit cell size on surface quality, deformation recovery, compression behavior, and energy absorption.
Haoming Mo, Shuo Qu, Shiming Gao, Xu Song   +3 more
wiley   +1 more source

Quantitative Defect-Property Correlations in Ti₃C₂T_x MXenes via Precursor-Controlled Defect Engineering. [PDF]

Nanomicro Lett
Hassan T, Lee D, Naqvi SM, Kim M, Oh JM, Park SW, Iqbal A, Cho SY, Hao Z, Hussain N, Khalid Z, Zaman S, Kong X, Roh KM, Kwon H, Koo CM.   +15 more
europepmc   +1 more source

Electrochemical Evaluation of Compressed Selective Laser Melted AlSi7Mg and AlSi10Mg Alloys in Chloride Environment

Advanced Engineering Materials, EarlyView.
The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin, Samson Dare Oguntuyi, Peter Apata Olubambi   +2 more
wiley   +1 more source

A unified active learning framework for photosensitizer design. [PDF]

Chem Sci
Chen Y, Verma S, Greenman KP, Yin H, Wang Z, Wang L, Li J, Gómez-Bombarelli R, Walsh A, Wang X.   +9 more
europepmc   +1 more source

Initial report on the radiative properties model

Initial report on the radiative properties model This report includes the description of the initial state of the art and the equations and models based on the new laboratory ...
openaire   +1 more source

Innovative Processing of Compacted Waste Aluminum Alloy Powders via Controlled Remelting and Solidification

Advanced Engineering Materials, EarlyView.
This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira, Marcella Gaute Cavalcante Xavier, Abdoul‐Aziz Bogno, Piter Gargarella, José Eduardo Spinelli   +4 more
wiley   +1 more source