Results 251 to 260 of about 15,316,992 (300)
Some of the next articles are maybe not open access.
Applied Energy, 2018
In this study, we conducted a numerical investigation on the effect of injection timing of boot injection rate shape on the combustion and emission characteristics in a direct injection compression ignition (DICI) engine fueled with kerosene/diesel ...
Dezhi Zhou +5 more
semanticscholar +1 more source
In this study, we conducted a numerical investigation on the effect of injection timing of boot injection rate shape on the combustion and emission characteristics in a direct injection compression ignition (DICI) engine fueled with kerosene/diesel ...
Dezhi Zhou +5 more
semanticscholar +1 more source
Measurement and validation of hole-to-hole fuel injection rate from a diesel injector
Flow Measurement and Instrumentation, 2018Hole-to-hole fuel injection characteristic differences that occurs during injection, results in non-uniform fuel distribution and compromised combustion and emission in direct injection IC engines.
T. Luo +5 more
semanticscholar +1 more source
Complication Rate of Power Coronary Angiography Injection
Angiology, 1980From 1970 to 1975, 1,498 patients underwent coronary angiography at Wilford Hall USAF Medical Center via the same injection technique utilizing a Viamonte Hobbs automatic volume injector. Most institutions now perform coronary angiography by hand injections of contrast medium, and automatic power injection angiography is reserved for ventriculograms ...
openaire +2 more sources
Rates of injection in prison in a sample of Australian-injecting drug users
Journal of Substance Use, 2013Aims: Determine the prevalence and frequency at which injecting drug users (IDU) continue to inject whilst incarcerated and to identify factors associated with in-prison injecting. Design: A nationally coordinated cross-sectional convenience sample. Participants: A total of 355 regular IDUs who had been imprisoned within the past 10 years.Measurements:
Fetherston, James +4 more
openaire +2 more sources
Experiments on Effect of Water Injection Rate on Imbibition Rate in Fractured Reservoirs
Fall Meeting of the Society of Petroleum Engineers of AIME, 1972Abstract A relationship has been established in the laboratory between rate of water injection into a simulated fracture-matrix type reservoir model and rate of imbibition. In a series of experiments involving linear countercurrent flow, it was discovered that the higher the water injection rate, the higher the ...
ROBERT W. MANNON, GEORGE V. CHILINGARIAN
openaire +1 more source
Optimization-based fuel injection rate digitalization for combustion rate shaping
2019 American Control Conference (ACC), 2019A major challenge of diesel engine development is the reduction of pollutant and CO 2 emissions. For that reason new solutions for clean and efficient combustion are investigated. One promising approach is the so-called combustion rate shaping. In this case the entire in-cycle resolved pressure or combustion rate trace is controlled by manipulating ...
Dennis Ritter +4 more
openaire +1 more source
A New Method for Measuring Fuel-Injection Rate
SAE Technical Paper Series, 1998<div class="htmlview paragraph">The paper deals with the method for measuring the diesel injection rate on the principle of gauging the fuel electric charge. Quoted are the physical principles on which the measuring method is based as well the results of testing</div>
openaire +1 more source
Minimizing Hydrate Inhibitor Injection Rates
International Petroleum Technology Conference, 2014Abstract Inhibitor injection is probably the most popular option for avoiding gas hydrate problems. However, inhibitor injection rates are normally designed based on worst operating conditions (i.e., maximum pressure and minimum temperature) with significant safety margin (e.g., 3–5 °C). Although the system pressure
Jinhai Yang +3 more
openaire +1 more source
2016
This report constitutes the main document of Deliverable 1.6 "Model of injection rates" of the Work Package WP1 of the H2020 project "MOSTOPHOS". The aim of this work is to parametrize the rate of charge injection from metal electrodes into organic materials, constituting the injection layer of the OLED stack.
openaire +1 more source
This report constitutes the main document of Deliverable 1.6 "Model of injection rates" of the Work Package WP1 of the H2020 project "MOSTOPHOS". The aim of this work is to parametrize the rate of charge injection from metal electrodes into organic materials, constituting the injection layer of the OLED stack.
openaire +1 more source
SIGNIFICANCE OF DISAPPEARANCE-RATE OF INJECTED INSULIN
The Lancet, 1967F I, Martin, A E, Stocks, M J, Pearson
openaire +2 more sources