Results 11 to 20 of about 32,865 (266)
Metals, 2021 In this paper, a pragmatic technique has been developed to evaluate the erosion-corrosion behavior of three kinds of ZrN coatings (i.e., monolayer, multilayer, and gradient layers) which were deposited on AISI 420 martensitic stainless steel using an ion-
Yuntao Xi +7 more
doaj +1 more source
XPS investigations of MOCVD tin oxide thin layers on Si nanowires array
Results in Physics, 2018 Tin oxide thin layers were grown by metal-organic chemical vapor deposition technique on the top-down nanostructured silicon nanowires array obtained by metal-assisted wet-chemical technique from single crystalline silicon wafers.
S.Yu. Turishchev +7 more
doaj +1 more source
Fushe yanjiu yu fushe gongyi xuebao, 2022 The S-band electron linear accelerator developed for nondestructive testing is primarily used to inspect pressure vessels, petrochemical parts, and other industrial components.
WANG Fei +4 more
doaj +1 more source
Selection of technologies for metal film application using physical deposition techniques
Advanced Engineering Research, 2020 Introduction. Obtaining high-quality thin metal films is important for advances in the technologies of applying antifriction and wear-resistant coatings on cutting tools or parts of friction couples.
S. P. Glushko
doaj +1 more source
Coatings on the Basis of Chromium Nitride. Experience of Design and Investigation
Успехи физики металлов, 2005 The investigation results concerning fabrication and application of Cr–N coatings, which are produced by the vacuum-arc evaporation, magnetron sputtering, and ion-beam-assisted deposition, are systematized.
A. G. Gyglya, I. M. Neklyudov
doaj +1 more source
Pulsed Laser-Assisted Helium Ion Nanomachining of Monolayer Graphene—Direct-Write Kirigami Patterns
Nanomaterials, 2019 A helium gas field ion source has been demonstrated to be capable of realizing higher milling resolution relative to liquid gallium ion sources. One drawback, however, is that the helium ion mass is prohibitively low for reasonable sputtering rates of ...
Cheng Zhang +7 more
doaj +1 more source
The energy flow in the course of thermal processing and during formation of thin films [PDF]
Computer Methods in Materials Science, 2005 Introduction to the modelling of the energy flow from electrodes through ionized gas to a heat affected zone (HAZ) during thermal processing and welding as well as the Ion Beam Assisted Deposition technique applied to formation of thin films is presented
Jacek Rońda +2 more
doaj +1 more source
Preparation of MgO Self-Epitaxial Films for YBCO High-Temperature Coated Conductors
Micromachines, 2023 Ion beam-assisted deposition (IBAD) has been proposed as a promising texturing technology that uses the film epitaxy method to obtain biaxial texture on a non-textured metal or compound substrate. Magnesium oxide (MgO) is the most well explored texturing
Fei Yu +6 more
doaj +1 more source
Mechanical properties of TiN coatings deposited at different temperatures by IBAD process [PDF]
FME Transactions, 2012 TiN coatings were deposited on hot working steel substrates by ion beam assisted deposition technique. The deposition process was conducted at two different temperatures 50 and 400 ºC.
Kakaš Damir +5 more
doaj
Room temperature deposition of superconducting niobium nitride films by ion beam assisted sputtering
APL Materials, 2018 We use room temperature ion beam assisted sputtering to deposit niobium nitride thin films. Electrical and structural characterizations were performed by electric transport and magnetization measurements at variable temperatures, X-ray diffraction, and ...
Tomas Polakovic +9 more
doaj +1 more source