Results 71 to 80 of about 400,516 (254)

Four‐Point Bending Tests at High Temperatures on Commercial MgO‐C Refractory Bricks with and Without Recyclate Considering Different Carbon Contents

Advanced Engineering Materials, EarlyView.
Four‐point bending tests are conducted in an argon atmosphere on commercial MgO‐C brick grades with and without MgO‐C recyclate from room temperature up to 1300 °C. No detrimental effect of the MgO‐C recyclates on bending strength is found. Instead, a decisive influence of the total carbon content is observed, with lower total carbon contents ...
Alexander Schramm, Lukas Knöchel, Thomas Schemmel, Christos G. Aneziris, Anja Weidner, Horst Biermann   +5 more
wiley   +1 more source

THE IMPACT OF MICRONUTRIENTS ON LABOR PRODUCTIVITY: EVIDENCE FROM RURAL INDIA [PDF]

Micronutrient malnutrition, particularly of iron, is widespread on the South Asian subcontinent and economic losses due to reduced productivity of afflicted population groups are believed to be substantial. This paper examines the impact of micronutrient
Weinberger, Katinka
core   +1 more source

Flux Weakening Strategy Optimization for Five-Phase PM Machine with Concentrated Windings [PDF]

, 2012
The paper applies an Efficient Global Optimization method (EGO) to improve the efficiency, in flux weakening region, of a given 5-phase Permanent Magnet (PM) machine. An optimal control for the four independent currents is thus defined.
ASLAN, Bassel, GILLON, Frédéric, JILIN, Gong, SEMAIL, Eric   +3 more
core   +4 more sources

A lower bound on the number of cosmic ray events required to measure source catalogue correlations

, 2016
Recent analyses of cosmic ray arrival directions have resulted in evidence for a positive correlation with active galactic nuclei positions that has weak significance against an isotropic source distribution.
Dolci, Marco, Romero-Wolf, Andrew, Wissel, Stephanie   +2 more
core   +1 more source

Population of Nonmetallic Inclusions in Liquid High‐Silicon Electrical Steel in Contact With MgO–C Refractories Based on Recyclates and Environmentally Friendly Binders

Advanced Engineering Materials, EarlyView.
The formation of nonmetallic inclusions (NMIs) was investigated in this study, carrying out immersion tests for 30 min at a temperature of 1600°C with liquid high‐silicon electrical steel (Si ≈ 3 mass‐%) and different MgO–C refractories. Conventional MgO–C refractories were considered, as well as MgO–C refractories containing MgO–C recyclate and ...
Lukas Neubert, Matheus Roberto Bellé, Florian Kerber, Dinesh Kumar Gunasekar, Hans‐Jörn Weddige, Christos G. Aneziris, Olena Volkova   +6 more
wiley   +1 more source

Corrosion and Process Analysis of a Preoxidized MgO Recyclate‐Based Cermet Anode in Laboratory‐Scale Na‐Cryolite Molten Salt Electrolysis of Aluminum at 1000°C

Advanced Engineering Materials, EarlyView.
EDX elemental map of the pre‐oxidized MgO–steel cermet anode cross section after electrolysis. The development of inert anodes for aluminum electrolysis remains challenging due to the high corrosivity of cryolite‐based melts at 950°C–1000°C. This study investigates the corrosion and process behavior of a carbon‐free MgO–steel cermet anode derived from ...
Alexander Adamczyk, Farhan Hossain, Felipe A. Garcia Paz, Serhii Yaroshevskyi, Felix Drechsler, Daniel Vogt, Christos G. Aneziris, Alexandros Charitos   +7 more
wiley   +1 more source

Resistance Rapid Heating of Aluminum Coatings in an Extreme High Vacuum–Adequate Atmosphere for Hot Stamping

Advanced Engineering Materials, EarlyView.
The subject of this work is the development of a corrosion‐protective coating on steel sheets for form hardening. Rapid heating in an extreme high vacuum (XHV)‐adequate atmosphere is a useful method to prevent oxidation during alloying of 22MnB5 and aluminum to obtain a metallurgical bonding.
Lorenz Albracht, Alexander Schnettger, Ulrich Holländer, Sven Hübner, Bernd‐Arno Behrens, Hans Jürgen Maier   +5 more
wiley   +1 more source

Surface Tension Measurement of Ti‐6Al‐4V by Falling Droplet Method in Oxygen‐Free Atmosphere

Advanced Engineering Materials, EarlyView.
In this article, the temperature‐dependent surface tension of free falling, oscillating Ti‐6Al‐4V droplets is investigated in both argon and monosilane doped, oxygen‐free atmosphere. Droplet temperature and oscillation are captured with one single high‐speed camera, and the surface tension is calculated with Rayleigh's formula.
Johannes May, Finn‐Lennard Janthur, Lena Kreie, Michael Müller, Sarah Seffer, Nick Schwarz, Jörg Hermsdorf, Thomas Hassel, Stefan Kaierle, Ludger Overmeyer   +9 more
wiley   +1 more source

Microstructure Evolution of a VMnFeCoNi High‐Entropy Alloy After Synthesis, Swaging, and Annealing

Advanced Engineering Materials, EarlyView.
The synthesis and processing (rotary swaging and annealing) of the novel VMnFeCoNi alloy is investigated, alongside the estimation of the grain size effect on hardness. Analysis of a wide grain size range of recrystallized microstructures (12–210 µm) reveals a low annealing twin density.
Aditya Srinivasan Tirunilai, Zeki Ayrildi, Buse Şen, Maik Rajkowski, Mathias Redondo Garcia, Markus Stricker, Guillaume Laplanche   +6 more
wiley   +1 more source

Bias‐Free Highly Efficient and Stable Dye‐Sensitized Photoelectrochemical Cells via Cascade Charge Transfer

Advanced Functional Materials, EarlyView.
A buried‐junction DSPEC design is introduced that leverages cascade charge transfer to enhance efficiency, stability, and versatility. This approach facilitates effective charge transfer and minimizes recombination losses, leading to significant improvements.
Jun‐Hyeok Park, Kyounglim Kim, Jinyoung Lee, Sarang Kim, Gwangsu Yoon, So Yeon Yoon, Jeong Kyeong Lee, Ji‐Wook Jang, Tae‐Hyuk Kwon   +8 more
wiley   +1 more source