Results 31 to 40 of about 1,982,243 (295)

Tribological behaviors of Ni-modified citric acid carbon quantum dot particles as a green additive in polyethylene glycol

open access: yesFriction, 2019
A novel green lubricating oil additive (carbon quantum dot (CQD) particle-doped nickel (Ni-CQD)) was synthesized from citric acid and nickel acetate. The effects of CQD and Ni-CQD nanoparticles on the tribological behaviors of polyethylene glycol (PEG200)
Zhiqiang Tu   +8 more
doaj   +1 more source

Research on Influence of Joint Clearance on Precision of 3-TPT Parallel Robot [PDF]

open access: yesMechanical Sciences, 2019
The error model of the working accuracy of parallel mechanism was established in this paper. The D-H matrix method and error independent method were used to analyze the clearance error of mechanism joint based on the inverse position kinematics solution.
C. Zhu, Z. Zhao
doaj   +1 more source

Error Uncertainty Analysis in Planar Closed-Loop Structure with Joint Clearances

open access: yesMetals, 2021
For planar closed-loop structures with clearances, the angular and positional error uncertainties are studied. By using the vector translation method and geometric method, the boundaries of the errors are analyzed.
Yushu Yu, Jinglin Li, Xin Li, Yi Yang
doaj   +1 more source

Nonlinear Dynamics and Control of Crank-Slider Mechanism with Multiple Clearance Joints [PDF]

open access: yesJournal of Theoretical and Applied Vibration and Acoustics, 2015
In the current study, behavior of crank-slider mechanism with single and multiple clearance joints are analyzed. Using Lankarani-Nikravesh theory for estimating discontinuous contact forces in clearance joints, relevant systems have been mathematically ...
Morteza Dardel   +3 more
doaj   +1 more source

Dynamic Analysis of a Delta Parallel Robot with Flexible Links and Joint Clearances

open access: yesApplied Sciences, 2023
Delta robot is a lightweight parallel manipulator capable of accurately moving heavy loads at high speed and acceleration along a spatial trajectory. This intensive dynamic process may have a significant impact on the end-effector trajectory precision ...
Nadia Cretescu   +2 more
doaj   +1 more source

The Effects of Joint Clearance on the Dynamics of the 3-RPR Planar Parallel Manipulator [PDF]

open access: yesInternational Journal of Advanced Design and Manufacturing Technology, 2018
In reality, clearances in the joints are inevitable due to the defects arising from manufacturing process, design tolerances, and wearing after a certain working period.
Seyyed Mojtaba Varedi-Koulaei   +1 more
doaj  

Pearson’s correlation between minimum toe clearance (MTC) variability and the variability of lower limb joint angles.

open access: yes, 2022
Pearson’s correlation between minimum toe clearance (MTC) variability and the variability of lower limb joint angles.
Prabhat Pathak (11902161)   +5 more
core   +1 more source

Dynamics and Wear Prediction of Mechanisms Considering Multiple Clearances and Coatings

open access: yesLubricants, 2023
The increase in joint clearance and system vibration caused by joint wear are important factors that may lead to the failure of the mechanism and a decrease in the motion accuracy of the actuator.
Qian Jing, Hongzhao Liu
doaj   +1 more source

Analysis of dynamic characteristics for momentum wheel assembly with joint clearance

open access: yesAdvances in Mechanical Engineering, 2018
To study the effects of joint clearance on the dynamic characteristics of the momentum wheel assembly of satellite antennas, the computational dynamic model of momentum wheel assembly is developed in this article, considering influencing factors ...
Qi Wan   +4 more
doaj   +1 more source

Nonlinear Characteristics of Revolute Joints with Clearance

open access: yesJournal of Aerospace Technology and Management, 2013
http://dx.doi.org/10.5028/jatm.v5i3.236 The nonlinear contact characteristic of revolute joint with clearance can degrade the performance of deployable structure. In this article, tensile and compressive tests are adopted to investigate the accuracies of the simplest conformal model and nonconformal model for contact, which are used to calculate the ...
Rong-qiang, Liu   +3 more
openaire   +5 more sources

Home - About - Disclaimer - Privacy