Results 81 to 90 of about 104,780 (198)

Experimental Evaluation of 100Cr6 Steel Microindented Surfaces Under Lubricated Nonconformal Point Contacts

Advanced Engineering Materials, EarlyView.
The tribological behavior of 100Cr6 steel spheres textured via Vickers microindentation is evaluated under lubricated sliding by varying both dimple size and density. Fine and dense textures significantly reduce friction across all lubrication regimes, while large dimples increase it.
Farideh Davoodi, Pasquale Guglielmi, Gianfranco Palumbo, Giuseppe Carbone   +3 more
wiley   +1 more source

Laser Powder Bed Fusion of Alumina: Effects of Scanning Strategies on External and Internal Defects

Advanced Engineering Materials, EarlyView.
This study investigates how scanning strategies affect pure alumina in laser powder bed fusion. Linear 45° scanning yields uniform surfaces but high porosity, while the island‐concentric strategy provides higher density with through‐holes favorable for infiltration. Findings highlight pathways toward optimizing defect‐free alumina parts.
Mohamed Abdelmoula, Gökhan Küçüktürk, Duran Kaya, David Grossin, Christophe Tenailleau, Benjamin Duployer, Enrique Juste, Fabrice Petit   +7 more
wiley   +1 more source

Effect of Low-power Laser on Treatment of Orofacial Pain

Journal of Dental Research, Dental Clinics, Dental Prospects, 2010
Low-power lasers are a group of lasers with a power less than 250 mW and unlike high-power lasers they have no effect on tissue temperature; they produce light-dependent chemical reactions in tissues.
Hamid Reza Khalighi , Fahimeh Anbari , Jamileh Beygom Taheri , Sedigheh Bakhtiari , Zahra Namazi, Firoz Pouralibaba   +5 more
doaj  

Carboxylic‐Acid Functionalized Multiwalled Carbon Nanotube‐Alkane‐Based Resistive Temperature Sensor for Cold Chain Applications

Advanced Engineering Materials, EarlyView.
This study presents a reversible temperature sensor with high switching ratio, ∼103. The device is fabricated using PET‐ITO and carbon nanotube dispersions in alkane. Considering its application in cold chain logistics, a proof‐of‐concept with LED is showcased. Thus, a temperature drop below the threshold temperature (crystallization temperature of the
Sunil Kumar Behera, Philippe Marrec, A. Jorge Parola, Madalena Dionísio, Hugo Águas, Andreia F. M. Santos, Hamed Pourkheirollah, Donald Lupo, César A. T. Laia   +8 more
wiley   +1 more source

Low‐Cost, Large‐Scale Nanoporous Metals by Mechanical Alloying, Oxide Reduction, and Dealloying of Powders

Advanced Engineering Materials, EarlyView.
Powder metal processing provides scalable advantages in nanoporous (np) metal development. Mechanical alloying is used to produce unique precursors for hybrid nanopore formation by oxide reduction and dealloying. As demonstrated in np Ag, this approach improves process efficiency while promoting smaller ligaments and larger pores, both of which are ...
Mark A. Atwater, Oliver A. Fowler
wiley   +1 more source

On the Lightweight Potential of Laser Additive Manufactured NiTi Triply Periodic Minimal Sheet Lattices

Advanced Engineering Materials, EarlyView.
This study explores the lightweight potential of laser additive‐manufactured NiTi triply periodic minimal surface sheet lattices. It systematically investigates the effects of relative density and unit cell size on surface quality, deformation recovery, compression behavior, and energy absorption.
Haoming Mo, Shuo Qu, Shiming Gao, Xu Song   +3 more
wiley   +1 more source

Electrochemical Evaluation of Compressed Selective Laser Melted AlSi7Mg and AlSi10Mg Alloys in Chloride Environment

Advanced Engineering Materials, EarlyView.
The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin, Samson Dare Oguntuyi, Peter Apata Olubambi   +2 more
wiley   +1 more source

Innovative Processing of Compacted Waste Aluminum Alloy Powders via Controlled Remelting and Solidification

Advanced Engineering Materials, EarlyView.
This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira, Marcella Gaute Cavalcante Xavier, Abdoul‐Aziz Bogno, Piter Gargarella, José Eduardo Spinelli   +4 more
wiley   +1 more source

A Workflow to Accelerate Microstructure‐Sensitive Fatigue Life Predictions

Advanced Engineering Materials, EarlyView.
This study introduces a workflow to accelerate predictions of microstructure‐sensitive fatigue life. Results from frameworks with varying levels of simplification are benchmarked against published reference results. The analysis reveals a trade‐off between accuracy and model complexity, offering researchers a practical guide for selecting the optimal ...
Luca Loiodice, Krzysztof S. Stopka, Michael D. Sangid   +2 more
wiley   +1 more source

Comparison of laser processability for LiFePO4 cathode material with nanosecond and femtosecond laser

Journal of Science: Advanced Materials and Devices
Exploration of increased electrode surface area through laser structuring is undertaken to improve performance. While nanosecond lasers offer cost-effective processing, femtosecond lasers achieve a minimal heat effect, excelling in precision.
Jaegeun Shin, Juhee Yang, Dongkyoung Lee
doaj   +1 more source