Results 11 to 20 of about 114,505 (312)
Laser based surface treatment of bioactive glass: Dependence on pulsed laser ablation
Applied Surface Science Advances, 2022 Experimental results and theoretical simulation of material ablation on nanosecond Nd:YAG laser irradiation of bioactive glass targets, is presented.
Sucharita Sinha
doaj +1 more source
Developments in the Built Environment, 2022 To identify the elastic wave excitation behavior by means of laser pulse irradiation on cementitious material surface in this study, the application of pulsed laser irradiation system for laser ablation and spallation technique can be explained and ...
Katsufumi Hashimoto, Tomoki Shiotani
doaj +1 more source
Scientific Reports, 2023 Two-photon stereolithography (TPS) is widely used for the fabrication of various three–dimensional (3D) structures with sub-micron fabrication resolution in a single fabrication process.
Cheol Woo Ha, Yong Son
doaj +1 more source
Safety of normal saline isolation zone: An experimental study on laser, radiofrequency and microwave thyroid thermal ablation [PDF]
Waike lilun yu shijian, 2020 Objective To investigate the safety of normal saline isolation zone in laser, radiofrequency and microwave thyroid ablation. Methods Fifteen pigs were divided into laser, radiofrequency and microwave three groups.
ZHAO Yanna, LIU Jun, HUANG Li, XU Wenjuan, NIE Zihuai, FEI Jian, GU Jianhua
doaj +1 more source
Yankuang ceshi, 2017 Understanding laser ablation behaviors of different target materials is essential for optimum laser parameters, external reference materials selection, as well as for data quality assurance.
WU Shi-tou +4 more
doaj +1 more source
Experimental Research and Numerical Simulation of Heat Transfer of Nanosecond Laser Ablation Wood
Chemical Engineering Transactions, 2016 By using nanosecond laser material ablation, which is widely used in mechanical micro machining fields. Based on this theory, in the northeast of red pine as the research object, establish the wood ablation heat transfer model, and derive the ...
Q. Guo, Y. Ma, Z. Wu, Y.L. Cui
doaj +1 more source
Laser ablation of lanthanum phosphate for pulsed laser deposition
International Journal of Ceramic Engineering & Science, 2021 A theoretical model has been used to simulate pulsed laser ablation of Lanthanum Phosphate (LaPO4) by nanosecond Nd:YAG laser irradiation. Material ablation rate per laser pulse was experimentally measured as a function of average incident laser fluence ...
Sucharita Sinha
doaj +1 more source
High-energy continuous wave laser ablation of alumina ceramic
Journal of Materials Research and Technology, 2023 The development of high-energy continuous wave (CW) laser has enabled the generation of output powers ranging from 300 to 500 kW. Understanding the ablation mechanism of CW lasers at high laser fluence is crucial for the design of effective high-energy ...
Xianshi Jia +11 more
doaj +1 more source
The impact of O/Si ratio and hydrogen content on ArF excimer laser ablation of fused silica [PDF]
Journal of the European Optical Society-Rapid Publications, 2014 The impact of stoichiometry and hydrogen content on the ArF excimer laser ablation characteristics of fused silica is investigated. Near-surface substoichiometic SiOx with X < 2 diminishes the ablation threshold as a result of increased absorption.
Tasche D. +4 more
doaj +1 more source
Characterization of the aerosol produced by infrared femtosecond laser ablation of polyacrylamide gels for the sensitive inductively coupled plasma mass spectrometry detection of selenoproteins [PDF]
, 2009 A 2D high repetition rate femtosecondlaserablation strategy (2-mm wide lane) previously developed for the detection of selenoproteins in gel electrophoresis by inductively coupled plasma mass spectrometry was found to increase signal sensitivity by a ...
Claverie, Fanny +11 more
core +1 more source