Results 41 to 50 of about 2,223,729 (213)

Thermomechanical Fatigue and Creep–Fatigue Interaction of Inconel 718 Additively Manufactured by Laser Beam Powder Bed Fusion

open access: yesAdvanced Engineering Materials, EarlyView.
Thermomechanical fatigue tests of laser beam powder bed fusion (PBF‐LB) Inconel 718 show that the additively manufactured material reaches almost the lifetimes of conventionally‐rolled material under no‐dwell conditions. Introducing dwell times at the maximum temperature markedly reduces the lifetimes due to pronounced grain boundary sliding associated
Stefan Guth   +6 more
wiley   +1 more source

Density Measurement of Irradiated and Nonirradiated Zirconium Oxide by Ptychographic X‐Ray Computed Tomography (PXCT)

open access: yesAdvanced Engineering Materials, EarlyView.
Mass density governs the protective behavior of oxide layers on nuclear fuel cladding. Ptychographic X‐ray computed tomography measures zirconium oxide grown on Zircaloy‐4 under reactor and autoclave conditions, revealing nearly identical bulk densities of 5.1 ± 0.80 g cm−3.
Okan Yetik   +9 more
wiley   +1 more source

Densification and preservation of ceramic nanocrystalline character by spark plasma sintering [PDF]

open access: yes, 2012
Spark plasma sintering is a hot pressing technique where rapid heating by dc electric pulses is used simultaneously with applied pressure. Thus, spark plasma sintering is highly suitable for rapid densification of ceramic nanoparticles and preservation ...
Estournès, Claude   +7 more
core   +1 more source

Computational and experimental models of induction flows in spark-ignition engines [PDF]

open access: yes, 1988
The objective of this thesis is to combine computational flow modelling, flow visualization and point measurements of mean flow and turbulence properties to obtain a better, more detailed, understandýing of the effects of alternative throttling ...
Sanatian, R.
core   +3 more sources

Influence of Scan Strategies in Electron Beam Powder Bed Fusion on Solidification, Microstructure, and High‐Temperature Compressive Properties of γ′‐Strengthened Inconel 738LC

open access: yesAdvanced Engineering Materials, EarlyView.
Experiments and thermophysical simulations were conducted to investigate the electron beam powder bed fusion electron beam (PBF‐EB/M) process for the γ′‐strengthened nickel‐based superalloy Inconel 738LC. The results demonstrate the impact of process‐induced microstructural variations on high‐temperature mechanical behavior, providing a basis for ...
Jan Niklas Petenati   +11 more
wiley   +1 more source

Impact of the Process Atmosphere During Hot Isostatic Pressing on the Near‐Surface Composition of an Additively Manufactured Austenitic High‐Interstitial Steel

open access: yesAdvanced Engineering Materials, EarlyView.
A high interstital austenitic steel is additively manufactured and postdensified by HIP to eliminate gas porosity. Thereby, the loss of N and Mn in Ar HIP atmosphere is investigated. Further, HIP using N2 atmosphere is investigated which led to excessive nitride formation.
F. Großwendt   +4 more
wiley   +1 more source

Electrodeposition in Structural Lattices of Variable Architectures

open access: yesAdvanced Engineering Materials, EarlyView.
Electrodeposition enables geometry‐sensitive, autonomous void filling while simultaneously tuning chemical and mechanical properties. The development of approaches that can autonomously fill and heal material voids and yield composites with tailorable properties is increasingly relevant in engineering.
Yeong‐Man Kwon   +3 more
wiley   +1 more source

Microstructure‑Dependent Phase Transformations Under High‑Pressure Laser Heating in Additively Manufactured AlCrFe2Ni2

open access: yesAdvanced Engineering Materials, EarlyView.
Additively manufactured AlCrFe2Ni2 with contrasting BCC/B2‐dominant and lamellar FCC + BCC/B2 microstructures exhibits the same pressure‐induced BCC/B2 → HCP transformation. Under laser heating at high pressure, HCP is destabilized, and a cubic BCC/B2 + FCC assemblage is recovered, while the lower‐scan‐speed microstructure transforms at a lower ...
Raimundas Sereika   +5 more
wiley   +1 more source

Impact of Hydrogen Incorporation on Electronic and Magnetic Structure of X2CrNi18‐9 Stainless Steel

open access: yesAdvanced Engineering Materials, EarlyView.
Hydrogen uptake in austenitic stainless steel alters both its electronic and magnetic structure. Seebeck measurements reveal hydrogen‐induced shifts in the electronic density of states, while neutron scattering uncovers nanoscale inhomogeneities that grow upon hydrogen incorporation, with the most pronounced effect observed in the PBF as‐built state ...
Torben Tappe   +9 more
wiley   +1 more source

Thermal Cycle–Microstructure–Property Relationships in Rail Steel Heat‐Affected Zone Simulated by Gleeble

open access: yesAdvanced Engineering Materials, EarlyView.
Microstructural evolution of premium rail steel during flash butt welding (FBW), comparing physically simulated heat‐affected zones with actual weld regions. Thermal cycles induce phase transformations and microstructural heterogeneity that influence weld quality and mechanical performance. These findings provide insights into optimizing FBW parameters
Emmanoelle Cintra da Cunha Araújo   +15 more
wiley   +1 more source

Home - About - Disclaimer - Privacy