Results 171 to 180 of about 3,427,330 (298)

Characterization of Defect Distribution in an Additively Manufactured AlSi10Mg as a Function of Processing Parameters and Correlations with Extreme Value Statistics

Advanced Engineering Materials, EarlyView.
Predicting extreme defects in additive manufacturing remains a key challenge limiting its structural reliability. This study proposes a statistical framework that integrates Extreme Value Theory with advanced process indicators to explore defect–process relationships and improve the estimation of critical defect sizes. The approach provides a basis for
Muhammad Muteeb Butt, Varma Kvvssn, Hossein Laieghi, Zia Uddin, Peyman Ansari, E. Kıvanç Sadak, Can Barış Toprak, Hüseyin Kızıl, Enrico Salvati   +8 more
wiley   +1 more source

Comparison of the Reliability and Gap Differences Between Using the Varus-Valgus Stress Technique and Paddles Technique in Pre-Resection Balancing Phase of Robotic-Assisted Total Knee Arthroplasty. [PDF]

Arthroplast Today
Narkbunnam R, Kittipibul K, Chareancholvanich K, Achawakulthep C, Awirotananon K, Pornrattanamaneewong C.   +5 more
europepmc   +1 more source

Experimental Evaluation of 100Cr6 Steel Microindented Surfaces Under Lubricated Nonconformal Point Contacts

Advanced Engineering Materials, EarlyView.
The tribological behavior of 100Cr6 steel spheres textured via Vickers microindentation is evaluated under lubricated sliding by varying both dimple size and density. Fine and dense textures significantly reduce friction across all lubrication regimes, while large dimples increase it.
Farideh Davoodi, Pasquale Guglielmi, Gianfranco Palumbo, Giuseppe Carbone   +3 more
wiley   +1 more source

The Lateral Alignment Angle: A Novel Method for Evaluating Lateral Patellar Tilt With High Accuracy, Good Reproducibility, and Independence From Patellofemoral Joint Morphology. [PDF]

Orthop Surg
Minghao L, Wen F, Qiang L, Guoqing C.
europepmc   +1 more source

Planar Solid‐State Nanopores Toward Scalable Nanofluidic Integration Based on CMOS Technology

Advanced Engineering Materials, EarlyView.
We present a scalable silicon‐based fabrication strategy for planar solid‐state nanopores to enable their integration with complex nanofluidic systems. Prototype devices demonstrate normal voltage‐current characteristics, good noise performance, and appreciable streaming currents. Our CMOS‐compatible fabrication process offers precise geometric control
Ngan Hoang Pham, Chenyu Wen, Mohammad Hadi Khaksaran, Won‐Yong Lee, Javier Cruz, Klas Hjort, Dongping Wu, Shi‐Li Zhang   +7 more
wiley   +1 more source

Caracterización articulatoria de ele en español y euskara

Estudios de Fonética Experimental, 2013
Este trabajo ofrece una caracterización y comparación de la producción de /l/ en castellano y euskara. Para ello, en primer lugar, se ha medido, mediante el software DicomPas, una colección de parámetros articulatorios establecida a partir del análisis ...
doaj  

Prediction of Surface Topography Parameters in Direct Laser Interference Patterning of Stainless Steel Using Infrared Monitoring and Convolutional Neural Networks

Advanced Engineering Materials, EarlyView.
This study presents an infrared monitoring approach for direct laser interference patterning (DLIP) combined with a convolutional neural network (CNN). Thermal emission data captured during structuring are used to predict surface topography parameters.
Lukas Olawsky, Marcelo Sallese, Leander Kläber, Clemens Kuhn, Keming Du, Andrés Fabián Lasagni   +5 more
wiley   +1 more source

Pathological features of the lateral joint capsule and lateral retinaculum in lateral patellar compression syndrome: a retrospective case-control study. [PDF]

BMC Musculoskelet Disord
Zhou S, Ding G, Yang S, Li N, Yang Y.
europepmc   +1 more source

Investigation of Laser Ablation and Brush Pre‐Treatments for AlCu Cold Roll Bonding in Oxygen‐Free Conditions

Advanced Engineering Materials, EarlyView.
It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti, Finn‐Lennard Janthur, Selina Raumel, Sascha Jan Zimmermann, Sarah Seffer, René Gustus, Sebastian Herbst, Marc C. Wurz, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Florian Nürnberger   +11 more
wiley   +1 more source

Coronal knee alignment is directly related to knee medial-to-lateral bone density ratio. [PDF]

J Exp Orthop
Klinger CE, Bilodeau RE, Mueller MM, Sculco PK, Rodeo SA, Gausden EB, Potter HG, Stein EM, Barth KA, Ricci WM, Hansen DG.   +10 more
europepmc   +1 more source