Results 91 to 100 of about 4,686,287 (314)

Geometry of fully augmented links in doubled 3-manifolds

Journal of Knot Theory and Its Ramifications
Classical fully augmented links have explicit hyperbolic geometry, and have diagrams on the 2-sphere in the 3-sphere. We generalize to construct fully augmented links projected to the reflection surface of any 3-manifold obtained by doubling a compact 3-manifold and show that the results of the classical setting extend to these links.
Jessica S. Purcell, Corbin Reid, John Stewart   +2 more
openaire   +3 more sources

Multiscale Modeling of Process‐Induced Defects in Fused Filament Fabrication‐Printed Materials

Advanced Engineering Materials, EarlyView.
This study presents a predictive multiscale modeling tool for defect analysis of fused filament fabricated‐printed materials and their performance prediction using a mechanistic data science‐based reduced‐order modeling approach. Process‐induced defects are inherent to additively manufactured parts and significantly influence the performance of printed
Satyajit Mojumder, Derick Suarez, Trevor Abbott, Wing Kam Liu   +3 more
wiley   +1 more source

Scaling tidal channel geometry with marsh island area: A tool for habitat restoration, linked to channel formation process [PDF]

, 2007
W. Gregory Hood
openalex   +1 more source

3D‐Printed Architected Material for the Generation of Foam‐Based Protective Equipment

Advanced Engineering Materials, EarlyView.
This study investigates 3D‐printed architected structures as alternatives to traditional foams in protective gear. It focuses on customizing impact strength and damping through design and manufacturing integration. Testing shows these structures outperform conventional foams, offering enhanced customizability, lower weight, and tunable performance ...
Ali Zolfagharian, Gerard Bel Català, Daniel Saakes, Bernard Rolfe, Ian Gibson, Mehrshad Mehrpouya   +5 more
wiley   +1 more source

Influence of Temperature on Scratch and Wear Properties of Technical Thermoplastics: Implications for Material Selection

Advanced Engineering Materials, EarlyView.
The share of technical thermoplastics is expected to grow further in the e‐mobility segment. In this study, a detailed temperature‐based tribological characterization of technical thermoplastics is performed. The tribological properties are discussed in terms of the dynamic mechanical properties of polymers at different ambient temperatures. A proof of
Harsha Raghuram, Thomas Koch, Vasiliki-Maria Archodoulaki   +2 more
wiley   +1 more source

X‐Ray Computed Tomography Quantifies Primary Phases and Reveals Crack Morphology in High‐Cycle Fatigue of Aluminum Alloy EN AW‐2618A

Advanced Engineering Materials, EarlyView.
Primary phases and a fatigue crack are studied in a forged blank of an aluminum alloy using synchrotron and laboratory X‐ray computed tomography. To image the crack, the fatigue test is interrupted, and a static tensile load is applied to open the crack.
Jakob Schröder, Ying Han, Tobias Fritsch, Bardia Hejazi, Alexander Ulbricht, Birgit Skrotzki, Giovanni Bruno   +6 more
wiley   +1 more source

Tribology of ZrC Coatings and Spherical Tips Acquired with Extraordinarily Stiff, Metal Atomic Force Microscopy Probes

Advanced Engineering Materials, EarlyView.
In this research, ZrC coatings are evaluated against various counterprobes at the microscale using novel super‐stiff atomic force microscopy cantilevers. The chemical composition of the coating is shown to be an important factor influencing coating hardness and Young's modulus, while surface roughness, counterprobe hardness, and surface energy are the ...
Piotr Jenczyk, Marcin Michałowski, Bogdan Warcholiński, Michał Milczarek, Adam Gilewicz   +4 more
wiley   +1 more source

Fabrication of a Stable, Low‐Cost, Patient‐Specific, Brain Phantom with Ventricles for Ultrasound Imaging

Advanced Engineering Materials, EarlyView.
Patient‐specific brain phantoms can replace animal trials, aid presurgical training, and enable in silico disease research on cerebrospinal fluid and ventricles. This study presents a method to create ventricular brain phantoms from three‐dimensional magnetic resonance images brain scans, resulting in durable, tunable, reproducible models that mimic ...
Kajal Chandraprakash Jain, Ana Belen Amado Rey, Ana Carolina Gonçalves Seabra, Thomas Stieglitz   +3 more
wiley   +1 more source

Influence of a Standard Heat Treatment on the Microstructure and Properties of Inconel X‐750 Produced by Laser Powder Bed Fusion

Advanced Engineering Materials, EarlyView.
Ni‐base superalloys produced using additive manufacturing (AM) have a different response to heat treatments when compared to their conventional counterparts. Due to such unpredictability, various alloys with industrial interest are currently overlooked in most prior AM research.
Guilherme Maziero Volpato, Adriano de Souza Pinto Pereira, Steffen Neumeier, Dachamir Hotza, Mathias Göken, Ulrich Tetzlaff, Márcio Celso Fredel   +6 more
wiley   +1 more source

Quality Enhancement of Laser Powder‐Bed Fusion Parts by Acoustically Assisted Additive Manufacturing by Laser Powder‐Bed Fusion and its Application to Lattice Structures

Advanced Engineering Materials, EarlyView.
Additive manufacturing technologies like laser powder‐bed fusion offer great design freedom and individualization of products down to a batch size of one. However, parts fabricated with this technology suffer from poor quality. Acoustic assistance during the build process can minimize these drawbacks.
Oliver Maurer, Dirk Bähre
wiley   +1 more source