Results 91 to 100 of about 402,850 (309)
Heave induced reduction of friction capacity of pile embedded in clays
MATEC Web of Conferences, 2017 Installation of new piles may cause heave which influence friction capacity of existing piles. The heave can be observed from the difference in the elevation of existing pile heads recorded before and after the installation of new piles or through load ...
Setyo Budi Gogot, Wibowo Tantri Gondo
doaj +1 more source
Perbandingan Kapasitas Dukung Aksial Pondasi Tiang Tunggal dengan Beberapa Metode Analisis (Studi Kasus : Pondasi Rumah Sakit Pendidikan Universitas Riau Pekanbaru) [PDF]
, 2014 A pile foundation design should be done carefully and as carefully as possible. Each foundation must be able to support loads up to the limit safely, including supporting the maximum load that may occur.
Muhardi, M. (Muhardi) +2 more
core
Annals of Clinical and Translational Neurology, EarlyView.ABSTRACT Background and Objectives Multiple sclerosis (MS) exhibits racially disparate rates of disease progression. Black people with MS (B‐PwMS) experience a more severe disease course than non‐Hispanic White people with MS (NHW‐PwMS). Here we investigated structural and functional connectivity as well as structure–function decoupling in the ...
Emilio Cipriano +11 more
wiley +1 more source
A Systematic Review and Meta‐Analysis of the Recurrence of Autoimmune Encephalitis
Annals of Clinical and Translational Neurology, EarlyView.ABSTRACT Objective Autoimmune encephalitis (AE) is a disease with a potential for recurrence, and patients receive immunotherapy to prevent it. However, there is no consensus on the duration of immunotherapy. This study aimed to determine the recurrence rate and identify the risk factors for AE to provide guidance on the duration of immunotherapy ...
Shangkai Bai +5 more
wiley +1 more source
CARRYING CAPACITY ANALYSIS OF CROSSED CYLINDRICAL ROLLER SLEWING BEARING UNDER COMBINED LOADS
Jixie qiangdu, 2016 The mechanics model of crossed cylindrical roller slewing bearing under combined radial,axial and tilting moment loads was established,this model considers the clearance parameter of the slewing bearing.
LI YunFeng, JIANG Di, CHENG YaBing
doaj
Computer program for flat sector thrust bearing performance [PDF]
A versatile computer program is presented which achieves a rapid, numerical solution of the Reynolds equation for a flat sector thrust pad bearing with either compressible or liquid lubricants.
Etsion, I., Presler, A. F.
core +1 more source
Bearing Capacity of Footings Under Inclined Loads
Soils and Foundations, 1971 synopsis A set up for footings under inclined loads has been described. Loads could be applied either (i) at an angle with vertical on a footing with horizontal base or (ii) normal to the footing with its base inclined with the horizontal. Typical observations on load, displacement, tilt and ultimate load carrying capacity of three footings on sand ...
Swami Saran +2 more
openaire +2 more sources
Location‐Specific Hematoma Volume Predicts Early Neurological Deterioration in Supratentorial ICH
Annals of Clinical and Translational Neurology, EarlyView.ABSTRACT Objective Early neurological deterioration (END) adversely affects outcomes in patients with intracerebral hemorrhage (ICH). This study aimed to determine the location‐specific hematoma volumes for END in supratentorial ICH patients. Methods We retrospectively analyzed supratentorial ICH patients presenting from two prospective cohorts.
Zuoqiao Li +10 more
wiley +1 more source
Effect of Pile and Load Inclination on the Pile Resistance In both Compression and Tension
Wasit Journal of Engineering Sciences, 2014 According to this theoretical study which was about loading of piles under different condition of loading (compression and up-lift forces ) and for deferent pile installation (vertical and inclined pile ) by which it called (positive batter pile )
Ahmad Jabber Hussain +2 more
doaj +1 more source
Optimum parallel step-sector bearing lubricated with an incompressible fluid [PDF]
The dimensionless parameters normally associated with a step sector thrust bearing are the film thickness ratio, the dimensionless step location, the number of sectors, the radius ratio, and the angular extent of the lubrication feed groove.
Hamrock, B. J.
core +1 more source