Results 51 to 60 of about 26,572 (214)

Observer‐Based Adaptive Event‐Triggered Tracking Control for Fuzzy TS Systems With Premise Mismatch

International Journal of Adaptive Control and Signal Processing, EarlyView.
This paper presents an adaptive logistic event‐triggered observer‐based tracking controller for Takagi‐Sugeno fuzzy systems under constrained inputs and network delays. Leveraging a hybrid LMI and Secretary Bird Optimization approach, this strategy significantly minimizes communication overhead and computational burden while ensuring optimal reference ...
Oussama Djadane, Salama Makni, Mourad Kchaou, Ahmed El Hajjaji   +3 more
wiley   +1 more source

Experimental and computational fluid dynamics-based numerical simulation of using natural gas in a dual-fueled diesel engine

Engineering Applications of Computational Fluid Mechanics, 2018
In this paper, investigations were performed on a dual-fueled constant-speed engine. Initially, the emissions and performance of a diesel engine were investigated, and after moving to the dual-fuel engine, experimental tests were carried out under ...
Eivaz Akbarian, Bahman Najafi, Mohsen Jafari, Sina Faizollahzadeh Ardabili, Shahaboddin Shamshirband, Kwok-wing Chau   +5 more
doaj   +1 more source

Numerical Simulation of the Influence of Platform Pitch Motion on Power Generation Steadiness in Floating Offshore Wind Turbines

Environmental Science and Sustainable Development, 2017
Offshore wind energy is a valuable renewable resource that is inexhaustible, strong, and consistent. To reduce cost and improve energy production efficiency, future trends are moving towards wind turbines in deep water, which use floating platforms such ...
Yehezkiel Tumewu, Petrone Crescenzo, Mettupalayam Sivaselvan   +2 more
doaj   +1 more source

Microstructural Evolution and Vacancy Defect Formation in Mn–Mo–Ni RPV Steel Under Low Cycle Fatigue: Insights From EBSD and PALS

Advanced Engineering Materials, EarlyView.
Low‐cycle fatigue damage in Mn–Mo–Ni reactor pressure vessel steel is examined using a combined electron backscatter diffraction and positron annihilation lifetime spectroscopy approach. The study correlates texture evolution, dislocation substructure development, and vacancy‐type defect formation across uniform, necked, and fracture regions, providing
Apu Sarkar, Dhanadeep Dutta, G. Bharat Reddy   +2 more
wiley   +1 more source

Thermodynamic Pathways of Nonequilibrium Solidification in Wire‐Arc Additive Manufacturing Fe‐Based Multicomponent Alloy Structures

Advanced Engineering Materials, EarlyView.
Geometry‐driven thermal behavior in wire‐arc additive manufacturing (WAAM) influences microstructural evolution during nonequilibrium solidification of a chemically complex Fe–Cr–Nb–W–Mo–C nanocomposite system. By comparing different deposits configurations, distinct entropy–cooling rate correlations, segregation, and carbide evolution are revealed ...
Blanca Palacios, Anthony Gonzalez, Aleksander Aleman, Tyler Dolmetsch, Tanaji Paul, Arvind Agarwal   +5 more
wiley   +1 more source

Thermomechanical Fatigue and Creep–Fatigue Interaction of Inconel 718 Additively Manufactured by Laser Beam Powder Bed Fusion

Advanced Engineering Materials, EarlyView.
Thermomechanical fatigue tests of laser beam powder bed fusion (PBF‐LB) Inconel 718 show that the additively manufactured material reaches almost the lifetimes of conventionally‐rolled material under no‐dwell conditions. Introducing dwell times at the maximum temperature markedly reduces the lifetimes due to pronounced grain boundary sliding associated
Stefan Guth, Tomáš Babinský, Jan Lars Riedel, Wen Hao Kan, Aijun Huang, Martin Heilmaier, Ivo Šulák   +6 more
wiley   +1 more source

Development of Simplified Methods for Levitation Force Distribution in Maglev Vehicles Using Frequency Ratio Tests

Sensors
Maglev vehicles apply the entire vehicle load uniformly onto bridges through levitation forces. In assessing the dynamic characteristics of the maglev train–bridge coupling system, it is reasonable to simplify the distributed levitation force as a ...
Wen Ji, Weihua Ma, Shihui Luo, Guofeng Zeng, Feng Ye, Mingbo Liu   +5 more
doaj   +1 more source

Low‐Temperature Imidization of Polyimides (PI) for Scalable Manufacturing of Flexible Wearable Electronics

Advanced Engineering Materials, EarlyView.
Low‐temperature imidization of PEG‐modified polyimide enables fully screen‐printed, roll‐to‐roll fabrication of flexible electrodes on PET substrates, delivering robust mechanical durability and reliable ECG/EMG signal performance for wearable electronics.
Akib Abdullah Khan, Jong‐Hoon Kim
wiley   +1 more source

Is an Apple an Orange? A Large Language Model Benchmark for Candidate Term Extraction and Subclass Decisions Against Upper Ontologies in Engineering and Materials Science

Advanced Engineering Materials, EarlyView.
Building machine‐readable vocabularies for materials science is slow, expert‐driven work. This study benchmarks 13 large language models on two of its first steps: finding candidate terms in engineering articles and deciding where they belong in a class hierarchy.
Thomas Bjarsch, Maximilian Holland, Klaus Drechsler, Johannes Schilp   +3 more
wiley   +1 more source

Current Status and Challenges in Data Collection for Aerospace Coatings Deposited by Plasma Spraying

Advanced Engineering Materials, EarlyView.
An innovative approach has been integrated into the GRENAT project to optimize plasma spraying and coating performance. Raw materials are accelerated and melted in the plasma generated by torches, creating coatings. Monitoring sensors collect process data which are combined with ex situ characterization data.
Lila Randriamananjara, Vincent Rat, Quentin Dubreuil, Patrice Valorge, Simon Goutier, Alain Denoirjean, Olivier Messe, Céline Ruelle, Jean‐Philippe Poli   +8 more
wiley   +1 more source