Results 151 to 160 of about 59,217 (275)
Advanced Engineering Materials, EarlyView.This study explores the lightweight potential of laser additive‐manufactured NiTi triply periodic minimal surface sheet lattices. It systematically investigates the effects of relative density and unit cell size on surface quality, deformation recovery, compression behavior, and energy absorption.
Haoming Mo +3 more
wiley +1 more source
Multi-Objective Optimization of Loop Closure Detection Parameters for Indoor 2D Simultaneous Localization and Mapping. [PDF]
Sensors (Basel), 2020 Han D, Li Y, Song T, Liu Z.
europepmc +1 more source
Duplex Stainless Steel Laser‐Surface Textured: Stability in Brine Solution
Advanced Engineering Materials, EarlyView.Controlled laser‐surface treatment (LST) of duplex DSS2205 steel is performed to increase its stability in brine solution under cyclic electrochemical assays. The superior protection with respect to flat and smooth panels is attributed to the presence of FeCr2O4 as the main protective oxide layer in the LST surface, after corrosion tests. The stability
Mohammad Rezayat +5 more
wiley +1 more source
Consumed by Abdominal Distention
Arthritis Care &Research, EarlyView.
Abimbola Fadairo‐Azinge +3 more
wiley +1 more source
A Workflow to Accelerate Microstructure‐Sensitive Fatigue Life Predictions
Advanced Engineering Materials, EarlyView.This study introduces a workflow to accelerate predictions of microstructure‐sensitive fatigue life. Results from frameworks with varying levels of simplification are benchmarked against published reference results. The analysis reveals a trade‐off between accuracy and model complexity, offering researchers a practical guide for selecting the optimal ...
Luca Loiodice +2 more
wiley +1 more source
Elinvar Materials: Recent Progress and Challenges
Advanced Engineering Materials, EarlyView.Elinvar materials, exhibiting temperature‐invariant elastic modulus, are critical for precision instruments and emerging technologies. This article reviews recent progress in the field, with a focus on the anomalous thermoelastic behavior observed in key material systems.
Wenjie Li, Yang Ren
wiley +1 more source
Advanced Engineering Materials, EarlyView.Low‐cycle fatigue damage in Mn–Mo–Ni reactor pressure vessel steel is examined using a combined electron backscatter diffraction and positron annihilation lifetime spectroscopy approach. The study correlates texture evolution, dislocation substructure development, and vacancy‐type defect formation across uniform, necked, and fracture regions, providing
Apu Sarkar +2 more
wiley +1 more source
Bile leakage after loop closure vs clip closure of the cystic duct during laparoscopic cholecystectomy: A retrospective analysis of a prospective cohort. [PDF]
World J Gastrointest Surg, 2020 Donkervoort SC +6 more
europepmc +1 more source
Advanced Engineering Materials, EarlyView.Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek +5 more
wiley +1 more source
3D‐Printed Giant Magnetoresistive (GMR) Sensors Based on Self Compliant Springs
Advanced Engineering Materials, EarlyView.This work explores 3D‐printed GMR sensors utilizing self‐compliant spring structures and conductive PLA composites. By optimizing arm width, we achieved high piezoresistive (0.34%/mm) and magnetoresistive (0.77%/mT) sensitivities. Demonstrated through Bluetooth‐integrated pressure and magnetic position sensing, these full printed low‐cost, customizable
Josu Fernández Maestu +4 more
wiley +1 more source