Results 151 to 160 of about 162,677 (314)
Advanced Engineering Materials, EarlyView.Low‐cycle fatigue damage in Mn–Mo–Ni reactor pressure vessel steel is examined using a combined electron backscatter diffraction and positron annihilation lifetime spectroscopy approach. The study correlates texture evolution, dislocation substructure development, and vacancy‐type defect formation across uniform, necked, and fracture regions, providing
Apu Sarkar +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek +5 more
wiley +1 more source
3D‐Printed Giant Magnetoresistive (GMR) Sensors Based on Self Compliant Springs
Advanced Engineering Materials, EarlyView.This work explores 3D‐printed GMR sensors utilizing self‐compliant spring structures and conductive PLA composites. By optimizing arm width, we achieved high piezoresistive (0.34%/mm) and magnetoresistive (0.77%/mT) sensitivities. Demonstrated through Bluetooth‐integrated pressure and magnetic position sensing, these full printed low‐cost, customizable
Josu Fernández Maestu +4 more
wiley +1 more source
Matching-range-constrained real-time loop closure detection with CNNs features. [PDF]
Robotics Biomim, 2016 Bai D, Wang C, Zhang B, Yi X, Tang Y.
europepmc +1 more source
Advanced Engineering Materials, EarlyView.Thermomechanical fatigue tests of laser beam powder bed fusion (PBF‐LB) Inconel 718 show that the additively manufactured material reaches almost the lifetimes of conventionally‐rolled material under no‐dwell conditions. Introducing dwell times at the maximum temperature markedly reduces the lifetimes due to pronounced grain boundary sliding associated
Stefan Guth +6 more
wiley +1 more source
Sol–Gel Derived Polymer Precursors for Stereolithography of ZrC
Advanced Engineering Materials, EarlyView.ZrC is a critical material target for extreme temperature conditions. This report describes a protocol for preparing ZrC ceramics via stereolithography and examines the impact of the polymer matrix on carbothermal reduction and mechanical stability of 3D printed ZrC.
Charles J. Rafalko +2 more
wiley +1 more source
A Knowledge‐Based Approach for Understanding and Managing Additive Manufacturing Data
Advanced Engineering Materials, EarlyView.Additive manufacturing processes generate a large amount of data. Effectively managing, understanding, and retrieving information from this data remains a major challenge. Therefore, we propose an ontology‐based approach to integrate heterogeneous data, enable semantic queries, and support decision‐making.
Mina Abd Nikooie Pour +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Collagen hydrolysate is evaluated as a sustainable binder for MgO‐C refractories. Its thermally induced cross‐linking and gas release lead to expansion and cracking in large bricks, but tailored batches with lignin, recyclates, or fine graphite improve the gas release while thermal treatment and stability.
Till M. J. Stadtmüller +8 more
wiley +1 more source
DTD: Density Triangle Descriptor for 3D LiDAR Loop Closure Detection. [PDF]
Sensors (Basel)Tang K, Wang Q, Yan C, Sun Y, Liu S.
europepmc +1 more source
Advanced Engineering Materials, EarlyView.This study develops sustainable MgO–C refractories using recycled materials and eco‐friendly fructose–tannin binders. The enhanced performance of citric acid as a cross‐linker and functional additives on mechanical and thermomechanical properties was examined. Characterization included strength tests, immersion trials, and microstructural and inclusion
Dinesh K. Gunasekar +7 more
wiley +1 more source