Results 241 to 250 of about 825,993 (315)

Low-Velocity Impact Resistance and Compression After Impact Strength of Thermoplastic Nanofiber Toughened Carbon/Epoxy Composites with Different Layups. [PDF]

Polymers (Basel)
Meireman T, Verboven E, Kersemans M, Van Paepegem W, De Clerck K, Daelemans L.   +5 more
europepmc   +1 more source

Encyclopedia of 2D β′‐In2Se3 Growth Using Chemical Vapor Deposition: The Effects of Synthesis Parameters Onto Material Quality

Advanced Engineering Materials, EarlyView.
A distinct semi‐confined inner‐tube chemical vapor deposition geometry enables reproducible, large‐area growth of phase‐pure 2D β′‐In2Se3 from InI + Se precursors. Engineering local vapor transport and optimizing precursor delivery and temperature–time conditions yield uniform continuous films.
Dasun P. W. Guruge, P. Sanju S. Panawala, Joseph F. S. Fernando, Zhenhuan Chen, Chao Zhang, Dong‐Chen Qi, Liangzhi Kou, Konstantin L. Firestein, Dmitri V. Golberg   +8 more
wiley   +1 more source

Effects of Rubber Core on the Mechanical Behaviour of the Carbon-Aramid Composite Materials Subjected to Low-Velocity Impact Loading Considering Water Absorption. [PDF]

Materials (Basel)
Ursache S, Cerbu C, Hadăr A, Petrescu HA.   +3 more
europepmc   +1 more source

Influence of Surface Finish on the Tribological Performance of AlTiBN Coatings Deposited on Forming Tools

Advanced Engineering Materials, EarlyView.
Aluminum and nitride coatings are used in industry because they are hard, resist wear, and protect against oxidation. Adding boron can improve friction behavior and other properties. This study tests coatings on surfaces with different finishes. Results show smoother surfaces perform better, while rough ones wear faster, although coatings can reduce ...
Adrián Claver, Iker Alfonso, Eneko Barba, Javier León, José Antonio García, Iñaki Zalakain, Iván Fernández Martínez, Arley García‐Carrero, Christian Almeyda, Daniel Salcedo   +9 more
wiley   +1 more source

Energy Absorption Behavior of Carbon-Fiber-Reinforced Plastic Honeycombs under Low-Velocity Impact Considering Their Ply Characteristics. [PDF]

Materials (Basel)
Liu Z, Zou K, Zhang Z.
europepmc   +1 more source

Experimental Characterization and Constitutive Modeling of the Effect of Prior Inelastic Strain on the Viscoplastic Behavior of AD730 at 700 °C

Advanced Engineering Materials, EarlyView.
This study shows that superalloys used in aircraft engine disks become much more prone to deformation at high temperatures if they have been strained during manufacturing. This effect increases with the level of prior strain but eventually reaches a limit.
Fabio Machado Alves da Fonseca, Patrick Villechaise, Malik Durand, Arnaud Longuet, Florent Coudon, Loïc Signor, Julien De Jaeger, Dominique Eyidi, Nathalie Bozzolo, Jonathan Cormier   +9 more
wiley   +1 more source

Study of Low-Velocity Impact Behavior of Hybrid Fiber-Reinforced Metal Laminates. [PDF]

Polymers (Basel)
Fang Y, Sheng D, Lin Z, Fei P.
europepmc   +1 more source

Low Cycle Repetitive Loading of Ti‐6Al‐4V‐Epoxy Composite Lattice Structures for Enhanced Energy Dissipation and Damage Tolerance

Advanced Engineering Materials, EarlyView.
Composite Ti–6Al–4V–epoxy lattice structures are additively manufactured and epoxy infiltrated for cyclic loading. At low lattice volume fractions, hybridization produces synergistic gains in stiffness and energy dissipation. At higher volume fractions, synergy diminishes, although composites still exceed metallic lattices in specific energy ...
Joey Tallon, Jordan Noronha, Justin Dirrenberger, Andrey Molotnikov   +3 more
wiley   +1 more source

An Experimental Investigation of the Mechanism of Hygrothermal Aging and Low-Velocity Impact Performance of Resin Matrix Composites. [PDF]

Polymers (Basel)
Zhang Y, Yan S, Wang X, Guan Y, Du C, Fan T, Li H, Zhai J.   +7 more
europepmc   +1 more source

Enhancing Bubble Removal in Geometry‐Optimized Electrodes

Advanced Engineering Materials, EarlyView.
3D‐printed lattice electrodes outperform stochastic foams in alkaline water electrolysis despite 20%–25% lower surface area. Straight flow channels generate Venturi‐like bubble entrainment, suppressing gas accumulation that renders foam interiors electrochemically inactive.
Florian Wiesner, Peter Förster, Alexander Limper, Anselm Brodersen, Matthias Wessling, John Linkhorst   +5 more
wiley   +1 more source