Results 101 to 110 of about 523,945 (348)
Advanced Engineering Materials, EarlyView.Carbon‐free inert anodes are essential for decarbonizing aluminum electrolysis. This study investigates a recyclate‐based MgO‐316L steel composite anode tested under galvanostatic Hall–Héroult conditions in cryolite at 1000°C. Microstructural analysis reveals selective MgO fluorination, spinel and oxide layer formation, electrolyte infiltration, and ...
Serhii Yaroshevskyi +7 more
wiley +1 more source
Removing Oxide Layers and Retaining Oxide‐Free Steel Surfaces by Polishing in Oxygen‐Free Atmosphere
Advanced Engineering Materials, EarlyView.In this study, the efficacy of wet mechanical polishing under an oxygen‐free atmosphere for deoxidation and the retention of an oxide‐free steel surface are elucidated using X‐ray photoelectron spectroscopy. The methodology proved successful; however, the results were highly dependent on the preparation of the solvents used to clean the samples after ...
Friedrich Bürger +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.The formation of nonmetallic inclusions (NMIs) was investigated in this study, carrying out immersion tests for 30 min at a temperature of 1600°C with liquid high‐silicon electrical steel (Si ≈ 3 mass‐%) and different MgO–C refractories. Conventional MgO–C refractories were considered, as well as MgO–C refractories containing MgO–C recyclate and ...
Lukas Neubert +6 more
wiley +1 more source
Advancing digital carbon management in China’s steel industry
工程科学学报To address global warming, respond to international trade pressures (such as carbon tariffs) affecting China’s iron and steel industry, and help the steel industry achieve the goal of “carbon peak + carbon neutrality,” this paper examines the current ...
Tao LI +7 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Through direct application of porous transport layer (PTL) on the bipolar plate (BPP) with thermal spraying, the interfacial contact resistance is improved. With the cold gas sprayed BPP–PTL coating system, a proton exchange membrane water electrolysis cell with a cell voltage of Ucell = 1.9 V can be operated up to i = 2.5 A/cm2 in a dynamic mode ...
Kirsten Bobzin +5 more
wiley +1 more source
Effect of carbonization on the mechanical properties of mild steel utilizing oak charcoal as a carbon source [PDF]
Engineering and Technology JournalCarburizing is a process that improves the mechanical properties of low-carbon steel, particularly its surface hardness. Introducing carbon into the steel's surface enhances the creation of a durable and resistant outer layer. The technique is ...
Omer Mahmood
doaj +1 more source
Pengaruh Kekasaran Permukaan Terhadap Sambungan Hasil Las Titik Pada Material Baja Karbon Rendah [PDF]
, 2015 Spot welding (spot welding) is the way in which the welding surface pressure plate connected with a large electrified through metal electrodes that intersect. In use the welding parameters greatly affect the outcome of the welding.
, Ir. Agus Hariyanto, M.T. +2 more
core
Advanced Engineering Materials, EarlyView.EDX elemental map of the pre‐oxidized MgO–steel cermet anode cross section after electrolysis. The development of inert anodes for aluminum electrolysis remains challenging due to the high corrosivity of cryolite‐based melts at 950°C–1000°C. This study investigates the corrosion and process behavior of a carbon‐free MgO–steel cermet anode derived from ...
Alexander Adamczyk +7 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Micro‐Raman spectroscopy is applied to characterize corrosion products in a recycled‐based MgO–316L steel composite anode after molten salt electrolysis. A depth‐dependent Fe–O/Fe–Al–O layer sequence of magnetite, hercynite, and an Al‐doped magnetite transition zone is identified.
Felix Drechsler +9 more
wiley +1 more source