Results 81 to 90 of about 10,522,925 (246)

3D‐Printed Titanium Gyroid Scaffold Structure Integrated With Tough Hybrid Materials for Cartilage Replacement

Advanced Engineering Materials, EarlyView.
This study proposes a potential device design for joint cartilage replacement. Silica‐polytetrahydrofuran (SiO2‐PolyTHF) hybrids with customizable mechanical properties were developed to mimic the characteristics of a natural meniscus. These were synthesized through a two‐pot sol–gel hybrid process.
Yu‐Chien Lin, Gloria R. Young, Francesca Tallia, Reece N. Oosterbeek, Shaaz Ghouse, Edward Spiers, Nupur Kohli, Tom Briggs, Marc Masen, Siwei Li, Ren‐Jei Chung, Jonathan R. T. Jeffers, Julian R. Jones   +12 more
wiley   +1 more source

Impact of the Process Atmosphere During Hot Isostatic Pressing on the Near‐Surface Composition of an Additively Manufactured Austenitic High‐Interstitial Steel

Advanced Engineering Materials, EarlyView.
A high interstital austenitic steel is additively manufactured and postdensified by HIP to eliminate gas porosity. Thereby, the loss of N and Mn in Ar HIP atmosphere is investigated. Further, HIP using N2 atmosphere is investigated which led to excessive nitride formation.
F. Großwendt, J. Hahn, J. Kimm, S. Weber, J. Lentz   +4 more
wiley   +1 more source

Advancing digital carbon management in China’s steel industry

工程科学学报
To address global warming, respond to international trade pressures (such as carbon tariffs) affecting China’s iron and steel industry, and help the steel industry achieve the goal of “carbon peak + carbon neutrality,” this paper examines the current ...
Tao LI, Xiuping LI, Fangqin SHANGGUAN, Wei ZHANG, Jicheng ZHOU, Bing NI, Zhiwei DUAN, Guoxiang TENG   +7 more
doaj   +1 more source

Enhancing Low‐Temperature Performance of Sodium‐Ion Batteries via Anion‐Solvent Interactions

Advanced Functional Materials, EarlyView.
DOL is introduced into electrolytes as a co‐solvent, increasing slat solubility, ion conductivity, and the de‐solvent process, and forming an anion‐rich solvent shell due to its high interaction with anion. With the above virtues, the batteries using this electrolyte exhibit excellent cycling stability at low temperatures. Abstract Sodium‐ion batteries
Cheng Zheng, Qian Yao, Yanan Sun, Hongyu Lv, Zhongchao Bai, Guoliang Zhang, Nana Wang, Jian Yang   +7 more
wiley   +1 more source

Research Progress on Corrosion Prevention Technology for Steel Reinforcement in Concrete with High-Volume Mineral Admixtures [PDF]

Cailiao Baohu
The utilization of active mineral admixtures as supplementary cementitious materials to partially replace cement not only aligns with the green and low-carbon development philosophy of the civil engineering and construction industry，but also represents a
AI Zhiyong, LI Xingqi, LIU Xianchao, HUANG Ling, GUO Xiaojun, SONG Dan
doaj   +1 more source

Laser‐Induced Graphene from Waste Almond Shells

Advanced Functional Materials, EarlyView.
Almond shells, an abundant agricultural by‐product, are repurposed to create a fully bioderived almond shell/chitosan composite (ASC) degradable in soil. ASC is converted into laser‐induced graphene (LIG) by laser scribing and proposed as a substrate for transient electronics.
Yulia Steksova, Anna Chiara Bressi, Marina Galliani, Attilio Marino, Gianni Ciofani, Eduardo Machado‐Charry, Hilda Gomez Bernal, Alessandra Francini, Luca Sebastiani, Francesco Greco   +9 more
wiley   +1 more source

Finance and state support for low-carbon steel

Decarbonising industry is a major 21st century challenge that requires international partnership, cooperation and corporate strategy. Historically ‘hard-to-abate’ sectors like steel are now central to this policy debate.
Selvaraju, Sangeeth
core   +1 more source

Advances in Sustainable and Wearable Textile Based Soft Robotics

Advanced Functional Materials, EarlyView.
This Review examines advances in wearable textile‐based soft robotics, focusing on sustainable materials, integrated sensing, and scalable actuation. It discusses manufacturing and system integration across healthcare, assistive robotics, prosthetics, and human–machine interfaces, and highlights key challenges in circular design, including life‐cycle ...
Zahir Abbas, Marzia Dulal, Sophia K. Novoselov, Victoria K. Novoselov, Kostya S. Novoselov, Shaila Afroj, Nazmul Karim   +6 more
wiley   +1 more source

Processing of low-carbon cast steels for offshore structural applications

, 2013
Cast steels with carbon contents of approximately 0.05%, 0.1%, and 0.2% (low-carbon steels) were processed. The investigated steels were first cast. Fully lath martensite was obtained after austenitization and water quenching of the cast steels.
Bolouri, Amir, Kang, Chung Gil, Kim, Tae Won   +2 more
core   +1 more source

Wear modelling of diamond-like carbon coatings against steel in deionised water

, 2014
Diamond-Like Carbon (DLC) coatings are thin protective surface coatings used to reduce friction and minimise wear in a wide range of applications. The focus of this work is the use of DLC coatings within Rolls-Royce’s pressurised water reactors. A strong
Sutton, Daniel Christopher
core   +1 more source