Results 61 to 70 of about 23,414 (253)
Fuel Communications, 2021 The desulfurization of four petroleum distillates i.e. kerosene, light gas oil (LGO), heavy gas oil (HGO) and light cycle oil (LCO), with sulfur content 0.206–1.272% w/w, was carried out using the hydrogen peroxide-acetic acid oxidative system, in ...
Eleni Syntyhaki, Dimitrios Karonis
doaj +1 more source
Advanced Engineering Materials, EarlyView.Si‐doped AlCoCrFeNi high‐entropy alloys are synthesized by mechanical alloying to reveal the effect of Si content and milling time on phase evolution, microstructural refinement, and tribological behavior. A transition from FCC to BCC structure, significant grain refinement, and enhanced hardness and wear resistance are achieved, with the 4 at% Si ...
Mustafa Okumuş +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal +3 more
wiley +1 more source
Tribology Online, 2022 The friction coefficient when a Fe surface was lubricated with an additive mixture of N-Oleoyl sarcosine (NOS), a commercial organic friction modifier, and zinc dialkyldithiophosphate (ZDDP) was measured at 100°C using a ball-on-disk tribometer under ...
Weiqi Shen +7 more
doaj +1 more source
Electrified Damage in Motion Systems
Advanced Engineering Materials, EarlyView.The electrified damage in motion systems is a fundamental framework presenting the degradation pathway arising from the coupling of electrical energy transport with mechanical contact and interfacial chemistry. The framework positions electrified damage as a distinct degradation regime with unique characteristic surface morphologies and failures of ...
M. Humaun Kabir +2 more
wiley +1 more source
FireThe combustion of liquid fuels that have leaked into inert porous media, such as sand, is a critical issue for industrial safety and fire risk assessment.
Keyu Lin +7 more
doaj +1 more source
, 2021 The objective of the present investigation is to analyze the tribological performance between the union of the cylinder liner and the compression ring under the influence of surface texturing and different lubrication boundary conditions. The analysis is
Sofia Orjuela Abril +5 more
core +1 more source
Active Corrosion Protection of Sintered AA7075 Aluminum Alloy via Mn Powder Addition
Advanced Engineering Materials, EarlyView.AA7075 containing Mn‐rich particles is fabricated via spark plasma sintering using AA7075 and Mn powders. Corrosion resistance is evaluated through dip‐and‐dry tests using 0.1 M NaCl (pH 6.0), and mass loss decreases with increasing Mn addition. Mn‐rich particles function as a source of Mn ions, and formation of Mn‐accumulation films on Cu‐containing ...
Ko Ebina, Masashi Nishimoto, Izumi Muto
wiley +1 more source
Acknowledgement to Reviewers of Lubricants in 2018
Lubricants, 2019 Rigorous peer-review is the corner-stone of high-quality academic publishing [...]
Lubricants Editorial Office
doaj +1 more source
Hybrid Metal–Carbon Ink for Printed Stretchable Temperature Sensors
Advanced Engineering Materials, EarlyView.We prepare conductive inks for temperature sensing with silver flakes and carbon or graphite flakes in a silicone elastomer matrix. Silver dominates the temperature‐dependent conductivity, while the carbon filler network ensures the stability of the conductive pathways and retains function under strain.
Makara Lay +3 more
wiley +1 more source