Results 41 to 50 of about 139,319 (359)
Lubrication and Lubricants [PDF]
, 2002 Lubrication is a process in which a lubricant is placed between rubbing surfaces to control friction and reduce wear. This article outlines the nature of the frictional force, the wear process, the role of surface characteristics, and the mechanisms of lubrication.
S., Nehal, M., Amal
openaire +2 more sources
Advanced Engineering Materials, EarlyView.This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira +4 more
wiley +1 more source
Tribology OnlineUsing a controlled atmosphere cutting apparatus equipped with a mass spectrometer, this study investigated the influence of several additive compounds on grease decomposition and hydrogen generation caused by a nascent clean steel surface.
Toshiaki Wakabayashi +3 more
doaj +1 more source
Effect of HFO Refrigerants on Lubrication Characteristics (Part 2)
Tribology Online, 2023 Following the previous paper focusing on tribological properties of hydrofluoroolefin (HFO) refrigerant, the adsorption behavior of refrigerants on the nascent iron surface was investigated experimentally and the adsorption structure, adsorption energy ...
Yuji Shitara +2 more
doaj +1 more source
Lubricant Social Marketing - Lessons Learned [PDF]
, 2002 With the most and longest experience social marketing lubricants, PSI is clearly the leader and within PSI is where the lessons learned primarily lie.
core
Advanced Engineering Materials, EarlyView.High‐temperature interactions between low‐sulfur Al‐killed Mn–B steel and MgO–C refractories (0 and 50 wt% recyclates) are studied via finger immersion tests (1600 °C). Surface‐active elements influence infiltration. MgO/CaS layer forms, along with spinel and calcium silicate.
Matheus Roberto Bellé +5 more
wiley +1 more source
Additives for Improving the Fuel Economy of Diesel Engine Systems
Tribology Online, 2010 Due to tightening CO2 emission regulations and increasing fuel prices, fuel economy has become one of the greatest issues facing society today. Although molybdenum dithiocarbamate (MoDTC) is a well-known friction modifier for gasoline engines, it has ...
Kenji Yamamoto +2 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti +11 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.ZnS‐MXene‐TiO2 nanocomposite heterojunction for photocatalytic decomposition of this methylene blue dye (MB) greatly improves light absorption, charge separation, and active site area. Two‐dimensional MXene forms nanocomposites by easily combining them with 0D (quantum dots), 1D (tube and wire), 2D (plane and sheet), and 3D (particle and lamellar ...
Latiful Kabir +7 more
wiley +1 more source
Removing Oxide Layers and Retaining Oxide‐Free Steel Surfaces by Polishing in Oxygen‐Free Atmosphere
Advanced Engineering Materials, EarlyView.In this study, the efficacy of wet mechanical polishing under an oxygen‐free atmosphere for deoxidation and the retention of an oxide‐free steel surface are elucidated using X‐ray photoelectron spectroscopy. The methodology proved successful; however, the results were highly dependent on the preparation of the solvents used to clean the samples after ...
Friedrich Bürger +2 more
wiley +1 more source