Results 11 to 20 of about 12,827 (224)
Journal of Manufacturing and Materials Processing, 2022 The paper discusses an instrumented tapping test method using a CNC machine tool to compare the lubricity of MWFs by cutting threads in a Ti-6Al-4V alloy at low speed. The method uses a spiral flute tap size typical of industrial practice.
Paul Wood +13 more
doaj +1 more source
Examination of lubricity properties of mineral base oil, containing nanoparticles of hexagonal boron nitride, and evaluation of the influence of surfactants on their sedimentation [PDF]
Biuletyn Wojskowej Akademii Technicznej, 2020 The article presents the results of tests on the lubricity properties of SN150 base oil containing hexagonal boron nitride (h-BN) of different granulation.
Arkadiusz Chodkiewicz +1 more
doaj +1 more source
Use of in vitro and haptic assessments in the characterisation of surface lubricity [PDF]
, 2018 Lubricity is a key property of hydrophilic-coated urinary catheter surfaces. In vitro tests are commonly employed for evaluation of surface properties in the development of novel catheter coating technologies, however, their value in predicting the more ...
Corbett, Dan J. +3 more
core +2 more sources
Lubricants, 2022 Ascorbyl palmitate (AP), known as a nutrition pill, and an antioxidant agent in food, has demonstrated excellent lubricity as an additive in PAO4. Adding one wt% AP in PAO4 drastically decreases friction Coefficient (CoF) up to 66% and protects the steel
Yun Long +6 more
doaj +1 more source
Lubricity of paraffinic fuels additivated with conventional and non-conventional methyl esters
Advances in Mechanical Engineering, 2019 Fuel lubricity prevents wear between metallic parts in relative motion inside the injection system of combustion engines. Among diesel fuels, paraffinic (gas-to-liquid or hydrotreated oils) and biodiesel (methyl esters) fuels are emerging since some of ...
José Rodríguez-Fernández +3 more
doaj +1 more source
The lubricity of ethanol-gasoline fuel blends
Revista Facultad de Ingeniería Universidad de Antioquia, 2013 In this work the lubricity of several ethanol (hydrated or anhydrous) / gasoline fuel blends was measured by using a conventional HFRR tester. Tests were carried out at 25ºC with no water vapour pressure control, according to the ASTM D6079 standard ...
John Agudelo +2 more
doaj +1 more source
Experimental viscosity measurements of biodiesels at high pressure [PDF]
, 2016 The viscosity of biodiesels of soybean and rapeseed biodiesels blended with mineral diesel fuel were measured at pressures of up to 200 MPa. Using a falling sinker-type viscometer reproducible viscosity data were obtained based on the time taken for a ...
Schaschke, Carl
core +4 more sources
Energies, 2023 Fuel contamination of engine lubricating oil has been previously determined to arise from two independent phenomena: the effect on oil flash point, and the effect of changing lubrication conditions on tribological pairs. This paper combines these effects
Leszek Chybowski
doaj +1 more source
Biodiesel as a lubricity additive for ultra low sulfur diesel [PDF]
Songklanakarin Journal of Science and Technology (SJST), 2010 With the worldwide trend to reduce emission from diesel engines, ultra low sulfur diesel has been introduced with thesulfur concentration of less than 10 ppm.
Subongkoj Topaiboul1 and 2,* +1 more
doaj
Slicing of silicon into sheet material: Silicon sheet growth development for the large area silicon sheet task of the Low Cost Silicon Solar Array project [PDF]
, 1978 The limits of blade tolerance were defined. The standard blades are T-2 thickness tolerance. Good results were obtained by using a slurry fluid consisting of mineral oil and a lubricity additive.
Fleming, J. R.
core +2 more sources