Results 241 to 250 of about 1,214,762 (295)

Design and Prototyping of Topology‐Optimized, Additively Manufactured Lightweight Components for Space Robotic Systems: A Case Study

Advanced Engineering Materials, EarlyView.
The results demonstrate a simulation‐driven workflow that applies LSB topology optimization with additive manufacturing constraints to mission‐specific load cases, integrating European Cooperation for Space Standardization compliant verification and manufacturability to develop structurally efficient rover suspension components.
Stelios K. Georgantzinos, Grigorios Kostopoulos, Eleni Papadopoulou, Stefanos Voulgaris, Alexandra Tseni, Panteleimon Bakalis, Maria N. Gkara, Chara Ch. Mitropoulou, Georgios Kazakis, Alin Munteanu, Jeremi Gancet, Nikos D. Lagaros   +11 more
wiley   +1 more source

Polyhydroxyalkanoate (PHA) Enriched with Diatomaceous Earth as a Sustainable Ecological Composite Material with the Possibility of Machining. [PDF]

Materials (Basel)
Gaweł A, Matras A.
europepmc   +1 more source

NFDI MatWerk Ontology (MWO): A BFO‐Compliant Ontology for Research Data Management in Materials Science and Engineering

Advanced Engineering Materials, EarlyView.
This article presents the NFDI‐MatWerk Ontology (MWO), a Basic Formal Ontology‐based framework for interoperable research data management in materials science and engineering (MSE). Covering consortium structures, research data management resources, services, and instruments, MWO enables semantic integration, Findable, Accessible, Interoperable, and ...
Hossein Beygi Nasrabadi, Ebrahim Norouzi, Kostiantyn Hubaiev, Jörg Waitelonis, Harald Sack   +4 more
wiley   +1 more source

Thin Wall Milling at a Maximized Axial Depth of Cut: An Analysis of Thermal and Mechanical Interactions. [PDF]

Materials (Basel)
Zawada-Michałowska M.
europepmc   +1 more source

Enhancing IoT Network Security through Prompt Intrusion Detection Using Machine Learning [PDF]

Ramineni Padmasree, Keerthana Muthyam
openalex   +1 more source

Mechanically Deposited Wear‐Resistant Amorphous Zr55Cu30Al10Ni5 Coatings

Advanced Engineering Materials, EarlyView.
Mechanically deposited from glassy ribbons, the Zr55Cu30Al10Ni5 amorphous coating formed a hard, continuous layer on AISI 1010 steel, tripling substrate hardness, lowering friction, and reducing wear. Despite its rough surface, it showed friction and wear behavior comparable to the crystalline alloy, highlighting its strong potential as a durable ...
Tales Ferreira, Pietro Cazelatto Bortolini, André Luiz Vidilli, Paulo Wilmar Barbosa Marques, Jéferson Aparecido Moreto, Claudio Shyinti Kiminami, Walter José Botta, Claudemiro Bolfarini, Guilherme Yuuki Koga   +8 more
wiley   +1 more source

A level set-based process planning method for the additive and subtractive hybrid manufacturing of a flow channel with an inner cavity. [PDF]

Sci Rep
Li L, Xu G, Ji H, Liu Y, Li X, Cai H, Zhao S, Zou B.   +7 more
europepmc   +1 more source

Devising statistic models of milking duration on the conveyor milking machines

, 2014
Володимир Юрійович Кучерук, Євген Анатолійович Паламарчук, Павло Ігорович Кулаков   +2 more
openalex   +2 more sources

Dry and Cryogenic Machining: Comparison from the Sustainability Perspective [PDF]

, 2011
Dillon, O.W., Jawahir, I.S., Lu, T., Rotella, Giovanna, Settineri, Luca   +4 more
core  

Interaction between Molten Al‐Killed Mn–B Steel and Carbon‐Bonded MgO Refractories Based on Recyclates

Advanced Engineering Materials, EarlyView.
High‐temperature interactions between low‐sulfur Al‐killed Mn–B steel and MgO–C refractories (0 and 50 wt% recyclates) are studied via finger immersion tests (1600 °C). Surface‐active elements influence infiltration. MgO/CaS layer forms, along with spinel and calcium silicate.
Matheus Roberto Bellé, Lukas Neubert, Anton Yehorov, Till M. J. Stadtmüller, Christos G. Aneziris, Olena Volkova   +5 more
wiley   +1 more source