Results 71 to 80 of about 25,943 (262)
Advanced Engineering Materials, EarlyView.The tribological behavior of 100Cr6 steel spheres textured via Vickers microindentation is evaluated under lubricated sliding by varying both dimple size and density. Fine and dense textures significantly reduce friction across all lubrication regimes, while large dimples increase it.
Farideh Davoodi +3 more
wiley +1 more source
La Presse MédicaleAbstract Vascular malformations are intricate anomalies of the circulatory system, presenting a diverse array of clinical manifestations, and posing significant challenges in diagnosis and treatment. The pathogenesis of vascular malformations is explored through the lens of genetic and molecular mechanisms, shedding light on the pivotal role ...
Neetu Bhari +4 more
openaire +5 more sources
Consumed by Abdominal Distention
Arthritis Care &Research, EarlyView.
Abimbola Fadairo‐Azinge +3 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This study presents a reversible temperature sensor with high switching ratio, ∼103. The device is fabricated using PET‐ITO and carbon nanotube dispersions in alkane. Considering its application in cold chain logistics, a proof‐of‐concept with LED is showcased. Thus, a temperature drop below the threshold temperature (crystallization temperature of the
Sunil Kumar Behera +8 more
wiley +1 more source
, 2013 <p>Since mid-December 2011, samples from malformed lambs and calves are sent to CODA-CERVA in Belgium for diagnosis of Schmallenberg virus (SBV), a novel Orthobunyavirus that was first detected by researchers of the Friedrich-Loeffler-Institut (FLI,
N. De Regge +3 more
core +1 more source
Advanced Engineering Materials, EarlyView.This study explores the lightweight potential of laser additive‐manufactured NiTi triply periodic minimal surface sheet lattices. It systematically investigates the effects of relative density and unit cell size on surface quality, deformation recovery, compression behavior, and energy absorption.
Haoming Mo +3 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin +2 more
wiley +1 more source
, 2017 (A-B) Embryos from a 12.5 days post coitum (dpc) litter harvested from a C57BL/6J female injected with ZIKV at 5.5 dpc. A, Malformed embryo displaying pericardial edema, unfused mandibular arch, missing hyoid arch, abnormal forelimbs and hindlimb ...
Vivian Vasconcelos Costa (3775309) +24 more
core +1 more source
Advanced Engineering Materials, EarlyView.This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira +4 more
wiley +1 more source
A malformed fetus in a rudimentary uterine horn pregnancy
, 2000 We present a case of a 13-week pregnancy with a malformed fetus in a ruptured non-communicating rudimentary horn. The patient, a 21-year-old woman with pelvic and right-sided abdominal pain, was admitted to the gynecology clinic of our institution.
Has, Recep, YILDIRIM, A, ERMIS, H
core +1 more source