Results 231 to 240 of about 1,282,960 (310)

Opportunities and barriers for innovation at the interface of engineering and maternal-fetal medicine. [PDF]

Commun Eng
Howlett TS, Parchem JG, Swingle KL.
europepmc   +1 more source

Handbook of Establishing and Maintaining Oxygen‐Free Atmospheres

Advanced Engineering Materials, EarlyView.
This study presents a practical framework for creating oxygen‐free atmospheres at ambient pressure using silane‐doped inert gases. The results show that ultra‐low oxygen levels and strongly reduced water content can be achieved through controlled silane dosing, drying systems, and sensor monitoring.
Sascha Jan Zimmermann, René Gustus, Lienhard Wegewitz, Wolfgang Maus‐Friedrichs   +3 more
wiley   +1 more source

Correction: Ryan Murphy et al. Investigating the Effect of Wire Drawing and Heat Treatment on the Response of Ni_50.9Ti_49.1 R-Phase Actuators. <i>Materials</i> 2025, <i>18</i>, 4931. [PDF]

Materials (Basel)
Ryan Murphy J, Obeidi MA, Ahad IU, Brabazon D.   +3 more
europepmc   +1 more source

Additive Gaussian Process Regression for Predictive Design of High‐Performance, Printable Silicones

Advanced Engineering Materials, EarlyView.
A chemistry‐aware design framework for tuning printable polydimethylsiloxane (PDMS) for vat photopolymerization (VPP) is developed using additive Gaussian process (GP) modeling. Polymer network mechanics informs variable groupings, feasible formulation constraints, and interaction variables.
Roxana Carbonell, Martha Leach, Hongtao Song, Carolyn Seepersad   +3 more
wiley   +1 more source

Surface Topography and Tolerance Quality Evaluation of Polymer Gears Using Non-Contact 3D Scanning Method. [PDF]

Materials (Basel)
Muratović E, Muminović AJ, Gierz Ł, Smailov I, Sydor M, Dizdarević E, Pervan N, Delić M.   +7 more
europepmc   +1 more source

Effect of Oxygen Content on Surface and Subsurface Integrity During Turning of Ti–6Al–4V

Advanced Engineering Materials, EarlyView.
This study examines how oxygen content in the ambient atmosphere affects the surface and subsurface properties of Ti–6Al–4V during turning. Results show that oxygen does not influence surface roughness. However, machining in an extremely high vacuum‐adequate atmosphere increases surface hardness by up to 7.8% and induces compressive residual stresses ...
Benjamin Bergmann, Berend Denkena, Hilke Petersen, Florian Schaper   +3 more
wiley   +1 more source

Advanced additive manufacturing in orthopedics: a comprehensive review of biomaterials, structural design, biological functions and clinical technology applications. [PDF]

RSC Adv
Chirume WM, Guo C, Zheng D, Ma F, Fan C, Li L, Wang L, Zhou C, Kong Q.   +8 more
europepmc   +1 more source

Oxide‐Free Titanium Coatings by Wire Arc Spraying in a Silane‐Doped Inert Atmosphere

Advanced Engineering Materials, EarlyView.
A silane‐doped argon atmosphere enables the production of oxide‐free titanium coatings via twin‐wire arc spraying at ambient pressure. This innovative approach eliminates residual oxygen, creating process conditions that prevent oxidation and nitride formation.
Manuel Rodriguez Diaz, Maik Szafarska, René Gustus, Kai Möhwald, Hans Jürgen Maier   +4 more
wiley   +1 more source

Polymer additive manufacturing tools for sheet metal forming: a combined simulation and experimental study. [PDF]

Sci Rep
Bhatia CV, Patel D, Vats R, Zameer MMF, Kumar R, Rajhi AA, Duhduh AA, Lozanovic J.   +7 more
europepmc   +1 more source

Application of Raman and Photoluminescence Spectroscopy to MgO‐C Refractories

Advanced Engineering Materials, EarlyView.
Visible to near infrared luminescence of MgO is studied on MgO‐C bricks and nominally pure MgO powder, with focus on two similar sharp high‐intensity signals, at 699 and 871 nm, each surrounded by symmetrical sidebands. The nature of these sidebands is investigated by temperature‐dependent spectroscopic measurements, confirming phonon involvement by ...
Julia Richter, Felix Drechsler, Till M. J. Stadtmüller, Cameliu Himcinschi, Christos G. Aneziris, Jens Kortus   +5 more
wiley   +1 more source