Results 81 to 90 of about 18,953 (211)

Experimental tests and empirical models of the cutting force and surface roughness when cutting 1Cr13 martensitic stainless steel with a coated carbide tool

Advances in Mechanical Engineering, 2016
Cutting force prediction is the key issue for planning and optimising the machining process. To explore the cutting of difficult-to-machine 1Cr13 martensitic stainless steel, an orthogonal test was conducted to study the cutting force and surface ...
Xu Chuangwen, Xu Ting, Yi Xiangbin, Zhang Jilin, Liu Wenli, Li Huaiyuan   +5 more
doaj   +1 more source

Investigation of surface residual stress profile on martensitic stainless steel weldment with X-ray diffraction

Journal of King Saud University: Engineering Sciences, 2018
The development of residual stresses during fabrication is inevitable and often neglected with dire consequences during the service life of the fabricated components.
I.I. Ahmed, J.A. Adebisi, S. Abdulkareem, A.H. Sherry   +3 more
doaj   +1 more source

Stress corrosion cracking evaluation of martensitic precipitation hardening stainless steels [PDF]

The resistance of the martensitic precipitation hardening stainless steels PH13-8Mo, 15-5PH, and 17-4PH to stress corrosion cracking was investigated. Round tensile and c-ring type specimens taken from several heats of the three alloys were stressed up ...
Humphries, T. S., Nelson, E. E.
core   +1 more source

Effect of temperature on the corrosion behavior of 13Cr stainless steel under a high CO2 partial pressure environment

工程科学学报, 2015
This article is focused on the effect of temperature on the corrosion electrochemical behavior of 13Cr martensitic stainless steel under a high temperature and high CO2 partial pressure environment.
LI Da-peng, ZHANG Lei, SHI Feng-xian, WANG Zhu, LI Hui, LU Min-xu   +5 more
doaj   +1 more source

Study made of resistance of stainless steels to zinc-vapor corrosion [PDF]

, 1967
Study of the corrosion resistance of several stainless steels to zinc vapor revealed that some stainless steels could be employed for use in zinc processing equipment housings or vapor ...
Bennett, G. A., Burris, L., Jr., Nelson, P. A.   +2 more
core   +1 more source

Fracture-tough, corrosion-resistant bearing steels [PDF]

The fundamental principles allowing design of stainless bearing steels with enhanced toughness and stress corrosion resistance has involved both investigation of basic phenomena in model alloys and evaluation of a prototype bearing steel based on a ...
Olson, Gregory B.
core   +1 more source

Studying the changes in the pressure transmission coefficient of the ultrasonic waves for ferrous and non-ferromagnetic alloys to find some of the most significant mechanical properties

Scientific Reports
This study is the most important part of the technique of using the pressure transmission coefficient (PTC) of the ultrasonic waves in extracting the most important mechanical properties (yield stress and ultimate strength) of alloys in general.
Arshed Abdulhamed Mohammed, Sallehuddin Mohamed Haris   +1 more
doaj   +1 more source

Effect of heat treatment on micro structure, hardness, high temperature oxidation resistance of martensitic stainless steel 13Cr3Mo3Ni-cast

Teknik, 2019
This paper reports the effect of heat treatment on microstructure, hardness and high-temperature oxidation resistance of martensitic stainless steels13Cr3Mo3Ni-cast.
Moch Syaiful Anwar, Eric Jonathan Yulianto, Septian Adi Chandra, Rahma Nisa Hakim, Sri Hastuty, Efendi Mabruri   +5 more
doaj   +1 more source

Stress corrosion cracking evaluation of several precipitation hardening stainless steels [PDF]

Stress corrosion cracking evaluation of several precipitation hardened stainless ...
Humphries, T. S., Nelson, E. E.
core   +1 more source

Rolling contact fatigue of surface modified 440C using a 'Ge-Polymet' type disc rod test rig [PDF]

Through hardened 440 C martensitic stainless steel test specimens were surface modified and tested for changes in rolling contact fatigue using a disc on rod test rig.
Thom, Robert L.
core   +1 more source