Results 271 to 280 of about 4,166,400 (347)

Manufacturing Continuous Fiber‐Reinforced Printing Filaments: Development of a Post‐Consolidation Unit

Advanced Engineering Materials, EarlyView.
A novel, temperature‐controlled post‐consolidation unit is developed to test its potential to improve the melt impregnation process used to manufacture continuous fiber‐reinforced filaments for additive manufacturing of high‐performance thermoplastics.
Daniel Beermann, Patrick Schiebel, David May   +2 more
wiley   +1 more source

Novel resilient solar photovoltaic power extraction strategy for rural AC micro grids with enhanced incremental conductance based MPPT. [PDF]

Sci Rep
Shanmugam P, Hussaini MM, Kumarasamy V, Thangavel J, Muthusamy S, Tirugatla SK, Paulsamy C, Salau AO.   +7 more
europepmc   +1 more source

Unidirectional Tape‐Based Composites from Hemp and Pineapple Leaf Fiber: Mechanical Performance in Conventional and Bio‐Based Matrices

Advanced Engineering Materials, EarlyView.
The study investigates novel semi‐finished products made of unidirectionally arranged hemp or pineapple leaf fiber‐reinforced composites produced from different matrices. The materials are analyzed in terms of their mechanical and interfacial properties and void content.
Nina Graupner, Raja Bade, Valentin Ackermann, Roja M. Baumann, Corvin Bischoff, Jona F. Ebeling, Oskar Glenz, Marlo Groh, Jonathan Groth, Finja Hiller, Tom Hirschmüller, Felix Menke, Syntcha Ngantchou Lecdou, Mika Ohler, Daniel Rafii Vardiny, Darius Richter, Dario Röper, Henrik Schumacher, Theresa Stein, Benjamin Vorbeck, Elisabeth Wermter, Kay Kölzig, Jörg Müssig   +22 more
wiley   +1 more source

Optimal control strategy for electric vehicle powered by PV arrays and battery using sliding mode control and linear quadratic regulator. [PDF]

Sci Rep
Gul BT, Rehman A, Sherazi HI, Alburidy A, Alsafrani A, Alrumayh O.   +5 more
europepmc   +1 more source

Rheocasting versus Die Casting: An Insight into the Low‐Cycle Fatigue Behavior of AlSi7Mg0.6

Advanced Engineering Materials, EarlyView.
The study compares rheocast lightweight components with high‐pressure die cast materials regarding microstructure and fatigue behavior. Rheocast process offers higher efficiency due to lower casting temperatures. Despite some microstructural differences, both processes show similar strengths (yield strength 125 MPa, tensile strength 240 MPa).
Julia Richter, Thomas Wegener, Andreas Schilling, Martin Fehlbier, Thomas Niendorf   +4 more
wiley   +1 more source

Multi-objective economic energy management strategy in thermal and electrical grids with energy hubs including renewable units and storage systems. [PDF]

Sci Rep
Mesloub A, Faridi W, Ghodratallah P, Rajab H, Singh NSS, Sadeq AM, Aich W, Shalaby M.   +7 more
europepmc   +1 more source

Fault-induced detection method for power supply lines in the cutting unit of coal shearer based on PIO-VMD-EDO. [PDF]

Sci Rep
Wang Y, Rong X, Shi H, Liu M, Guo X, Cheng Z, Wang W.   +6 more
europepmc   +1 more source

Bioinspired STHVO based MPPT control for grid connected photovoltaic water pumping systems. [PDF]

Sci Rep
Ballouti A, Chouiekh M, Ameziane H, Zakriti A, El Mourabit Y, Bacanin N, Nikolic B, Karmouni H, Abouhawwash M.   +8 more
europepmc   +1 more source

Enhanced adaptive control techniques for extracting maximum power from photovoltaic system. [PDF]

Sci Rep
Hafez AO, Attia MA, El-Ebiary AH.
europepmc   +1 more source

UAV-Assisted Covert Communication with Dual-Mode Stochastic Jamming. [PDF]

Sensors (Basel)
Gu M, Su Y, Ma Z, Lian Z, Wang Y.
europepmc   +1 more source