Results 21 to 30 of about 8,047,163 (238)
Effect of Hot-Rolling on the Microstructure and Impact Toughness of an Advanced 9%Cr Steel
Crystals, 2023 A 9%Cr martensitic steel with Ta and B additions was subjected to thermo-mechanical treatment (TMT) including rolling in the range of metastable austenite at 900–700 °C followed by water quenching and tempering at different temperatures. Applied TMT with
Evgeniy Tkachev +2 more
doaj +1 more source
Effect of Tungsten on Creep Behavior of 9%Cr–3%Co Martensitic Steels
Metals, 2017 The effect of increasing tungsten content from 2 to 3 wt % on the creep rupture strength of a 3 wt % Co-modified P92-type steel was studied. Creep tests were carried out at a temperature of 650 °C under applied stresses ranging from 100 to 220 MPa with a
Alexandra Fedoseeva +3 more
doaj +1 more source
Mechanical properties of mesoporous ceria nanoarchitectures [PDF]
, 2014 Architectural constructs are engineered to impart desirable mechanical properties facilitating bridges spanning a thousand meters and buildings nearly 1 km in height.
Sayle, T.X.T. +10 more
core +1 more source
The mechanical and ballistic properties of polycarbonate [PDF]
, 2008 Polycarbonate is commonly used as the material of riot shields. Firings of 8.3 g steel ball bearings at velocities of 23-98 ms-1 produced damage in the form of dents.
Edwards, Michael R., Waterfall, H.
core +7 more sources
Effect of Si and Zr on the Microstructure and Properties of Al-Fe-Si-Zr Alloys
Metals, 2017 The effects of Si and Zr on the microstructure, microhardness and electrical conductivity of Al-Fe-Si-Zr alloys were studied. An increase in the Zr content over 0.3 wt.
Anna Morozova +6 more
doaj +1 more source
Experimental study of the particle agglomeration on its mechanical properties of collapsible loess
Frontiers in Earth Science, 2022 Loess, distributed all over the world, exhibits the behavior that is related to their formation history, mineralogy, and microstructure, which can cause serious geotechnical engineering problems.
Meng Zhao +7 more
doaj +1 more source
Improving Mechanical Properties of 18%Mn TWIP Steels by Cold Rolling and Annealing
Metals, 2019 The microstructures and mechanical properties of Fe-0.4C-18Mn and Fe-0.6C-18Mn steels subjected to large strain cold rolling followed by annealing were studied.
Vladimir Torganchuk +2 more
doaj +1 more source
Creep and Deformation of Metals and Alloys at Elevated Temperatures
Metals, 2021 Various aspects of creep and deformation behaviors of metals and alloys at elevated temperatures are of great interest to materials scientists [...]
Nadezhda Dudova
doaj +1 more source
Metals, 2017 The structure–property relationship was studied in an Fe-18Mn-0.6C-1.5Al steel subjected to cold rolling to various total reductions from 20% to 80% and subsequent annealing for 30 min at temperatures of 673 to 973 K.
Alexander Kalinenko +4 more
doaj +1 more source
Journal of Materials Research and Technology, 2022 PIII nitriding was applied to superaustenitic steel to improve wear resistance without compromising pitting and hydrogen embrittlement corrosion resistance. Nitriding at temperatures between 300 °C and 400 °C produced modified layers rich in γN phase and
Bruna C.E. Schibicheski Kurelo +5 more
doaj +1 more source