Results 71 to 80 of about 70,412 (305)
Anisotropic Boundary Layer Adaptivity of Multi-Element Wings
, 2014 Multi-element wings are popular in the aerospace community due to their high lift performance. Turbulent flow simulations of these configurations require very fine mesh spacings especially near the walls, thereby making use of a boundary layer mesh ...
Chitale, Kedar C. +4 more
core +1 more source
A computationally-efficient numerical model to characterize the noise behavior of metal-framed walls [PDF]
, 2015 Architects, designers, and engineers are making great efforts to design acoustically-efficient metal-framed walls, minimizing acoustic bridging. Therefore, efficient simulation models to predict the acoustic insulation complying with ISO 10140 are needed
Arjunan, Arun +4 more
core +2 more sources
Arthritis Care &Research, Accepted Article.Background Clinical response to Mycophenolic acid (MPA) is highly heterogeneous; thus, therapeutic drug monitoring (TDM) may help improve treatment efficacy. This systematic review and meta‐analysis examined therapeutic ranges for MPA levels associated with better outcomes and safety in patients with SLE, particularly those with extra‐renal ...
Zahraa Qamhieh +5 more
wiley +1 more source
Jixie chuandong, 2017 The generating plane inclination angle has a great influence on the meshing performance of the plane enveloping internal meshing worm drive,and it has a decisive role in determining the optimal parameters of the plane enveloping internal meshing worm ...
Feng Zhipeng +3 more
doaj
Finite Element Flow Simulations of the EUROLIFT DLR-F11 High Lift Configuration
, 2014 This paper presents flow simulation results of the EUROLIFT DLR-F11 multi-element wing configuration, obtained with a highly scalable finite element solver, PHASTA. This work was accomplished as a part of the 2nd high lift prediction workshop.
Chitale K. C. +7 more
core +1 more source
The low-noise optimisation method for gearbox in consideration of operating conditions [PDF]
, 2014 This paper presents a comprehensive procedure to calculate the steady dynamic response and the noise radiation generated from a stepping-down gearbox.
Kang, J, Sun, W, Tao, Q, Zhou, J
core +1 more source
Advanced Engineering Materials, Volume 27, Issue 6, March 2025.ErB4 and NdB4 nanostructured powders are produced by mechanochemical synthesis. 5 h mechanical alloying and 4 M HCl acid leaching are used in the production. ErB4 and NdB4 powders exhibit maximum magnetization of 0.4726 emu g−1 accompanied with an antiferromagnetic‐to‐paramagnetic phase transition at about TN = 18 K and 0.132 emu g−1 with a maximum at ...
Burçak Boztemur +5 more
wiley +1 more source
A Novel Method for the Fault Diagnosis of a Planetary Gearbox based on Residual Sidebands from Modulation Signal Bispectrum Analysis [PDF]
, 2014 This paper presents a novel method for the fault diagnosis of planetary gearboxes based on an accurate estimation of residual sidebands using a modulation signal bispectrum (MSB).
Abdalla, Gaballa M. +4 more
core
Bistable Mechanisms 3D Printing for Mechanically Programmable Vibration Control
Advanced Engineering Materials, EarlyView.This work introduces a 3D‐printed bistable mechanism integrated into tuned mass dampers (TMDs) for mechanically adaptive passive vibration suppression. Through optimized geometry, the bistable design provides adaptable vibration reduction across a broad range of scenarios, achieving effective vibration mitigation without complex controls or external ...
Ali Zolfagharian +4 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Laser surface texturing significantly improves the corrosion resistance and mechanical strength of 3D‐printed iron polylactic acid (Ir‐PLA) for marine applications. Optimal laser parameters reduce corrosion by 80% and enhance tensile strength by 25% and ductility by 15%.
Mohammad Rezayat +6 more
wiley +1 more source