Results 131 to 140 of about 7,957 (309)

Photocatalytic Water Splitting on the Lunar Surface: Prospects for In Situ Resource Utilization

Advanced Materials Interfaces, EarlyView.
Water has been found in craters on the moon nearby locations which are illuminated >80% of the time. Photocatalysis uses energy from sunlight to drive chemical reactions such as water splitting to produce oxygen and hydrogen. It is a scalable technology that requires lighter equipment and utilizes resources available on the moon. ABSTRACT The discovery
Ranjani Kalyan, Thomas D. Small, Gregory F. Metha, Mahmoud Adel Hamza, Thomas J. O'Dea, Yideng Shen, Cameron J. Shearer   +6 more
wiley   +1 more source

Desenvolvimento de novos tipos de aços sinterizados autolubrificantes a seco com elevada resistência mecânica aliada a baixo coeficiente de atrito via moldagem de pós por injeção [PDF]

, 2012
Tese (doutorado) - Universidade Federal de Santa Catarina, Centro Tecnológico, Programa de Pós-Graduação em Ciência e Engenharia de Materiais, Florianópolis, 2009No presente trabalho foram desenvolvidos aços sinterizados autolubrificantes a seco ...
Binder, Cristiano
core  

Energy Band Alignment and Electro‐Optical Behavior of Nearly Unstrained Monolayer MoS2 Heterostructures With GaN

Advanced Materials Interfaces, EarlyView.
Large size (∼100 µm) monolayer MoS2 grown by LPI‐CVD on n‐GaN exhibit a high n‐type doping, very low strain, and a type‐I band alignment at MoS2/GaN interface. Photocurrent measurements under illumination with photon energies from ∼2 to ∼5 eV show superior electro‐optical performances of these MoS2/n‐GaN heterojunctions as compared to Ni/n‐GaN devices ...
Salvatore Ethan Panasci, Emanuela Schilirò, Giuseppe Greco, Patrick Fiorenza, Fabrizio Roccaforte, Fiorenza Esposito, Igor Píš, Federica Bondino, Antonino Madonia, Marco Cannas, Simonpietro Agnello, Luca Seravalli, Filippo Giannazzo   +12 more
wiley   +1 more source

Influence of the Injection Process on Two-Phase Separation in Stainless-Steel Metal Powder Injection Molding

Metals
A common issue encountered in metal powder injection molding is the separation of the powder and binder during the injection process, which can give rise to a number of defects.
Yan Li, Xingjie Peng, Xiang Zan, Laima Luo, Yucheng Wu   +4 more
doaj   +1 more source

MANUFACTURING OF METAL AND CERAMIC PRODUCTS BY INJECTION MOLDING

, 2020
Tema ovog diplomskog rada je izrada metalnih i keramičkih proizvoda postupkom injekcijskog prešanja. U radu su opisani materijali, koji se koriste u postupku injekcijskog prešanja, i njihove karakteristike.
Pašalić, Ante
core  

BioEISense: A Microfluidic Platform for Real‐Time Monitoring of Staphylococcus aureus Biofilm Formation and the Efficacy of Antibiofilm Agents

Advanced Materials Interfaces, EarlyView.
BioEISense is a microfluidic device with integrated impedance sensors, for real‐time, label‐free monitoring of S. aureus biofilms. In this study, the biofilm culture conditions were optimized to support sensitive and reproducible detection of biofilm formation and eradication under dynamic flow‐through conditions. The system was also validated for both
Jéssica Amorim, Laura Vesalainen, Loïc Dreano, Markus Haapala, Cristina D. Cruz, Päivi Tammela, Tiina M. Sikanen   +6 more
wiley   +1 more source

Desenvolvimento de compósito de resina epóxi e fibras curtas de aço para fabricação rápida de moldes para injeção de termoplásticos [PDF]

, 2008
Tese (doutorado) - Universidade Federal de Santa Catarina, Centro Tecnológico. Programa de Pós-Graduação em Engenharia MecânicaTem sido cada vez mais crescente a procura por ferramentas de projeto que possibilitem avaliar o desempenho de um produto em ...
Sabino Netto, Aurélio da Costa
core  

Femtosecond‐Laser Mould Texturing Enables Tunable Biointerfaces in COC Microfluidics

Advanced Materials Interfaces, EarlyView.
Femtosecond‐laser texturing of injection‐mould inserts enables scalable engineering of biointerfaces in cyclic olefin copolymer microfluidics. Replicated micro‐ and nano‐topographies modulate surface roughness and wettability, leading to texture‐dependent protein adsorption and cell adhesion without chemical post‐processing.
Irene Varela‐Leniz, Nora Larreategi, Laura Gemini, Taieb Bakouche, Florent Husson, Leire Gartzia‐Rivero, Eider Bilbao Castellanos, Ane Miren Zaldua, José Luis Vilas‐Vilela, Leire Etxeberria   +9 more
wiley   +1 more source

Comparison of slot sizes and parallelism of metal brackets manufactured through metal injection molding and computerized numerical control. [PDF]

Korean J Orthod, 2020
Park JS, Song IT, Bae JH, Gil SM, Kang KH.   +4 more
europepmc   +1 more source

Enhanced Infection Resistance and Regenerative Healing of Titanium Implants via Peptide‐Loaded Biodegradable Coatings

Advanced Materials Technologies, EarlyView.
This study presents a new biodegradable coating for titanium implants using a natural antimicrobial peptide, caerin 1.9. Applied via solvent casting, the coating offers sustained antibacterial protection and promotes healing. Tested on 3D‐printed porous titanium scaffolds, it effectively prevented infection—including against resistant bacteria—while ...
Hejie Li, Tianfang Wang, Nicolas Soro, Guoying Ni, Meg Allom, D. İpek Kurtböke, Xiaosong Liu, Damon Kent   +7 more
wiley   +1 more source