Results 171 to 180 of about 107,094 (346)

Conductive Hydrogels for Exogenous Sensing and Cell Fate Control

Advanced Materials, EarlyView.
We engineer electrically conductive hydrogels by combining sulfated glycosaminoglycans with semiconducting polymers. These hydrogels bind bioactive proteins, including growth factors, whose release or retention can be modulated by low‐voltage stimulation. The hydrogels are also integrated as 3D channels in organic electrochemical transistors as part of
Teuku Fawzul Akbar, Carlos Alejandro Jimenez‐Rodriguez, Railia Biktimirova, Ilka Hermes, Thomas Kurth, My Duyen Pham, Mikhail Tsurkan, Jens Friedrichs, Francis L. C. Morgan, Hans Kleemann, Olga Guskova, Uwe Freudenberg, Peter Fratzl, Carsten Werner, Christoph Tondera, Ivan R. Minev   +15 more
wiley   +1 more source

Photocatalytic Water Splitting on the Lunar Surface: Prospects for In Situ Resource Utilization

Advanced Materials Interfaces, EarlyView.
Water has been found in craters on the moon nearby locations which are illuminated >80% of the time. Photocatalysis uses energy from sunlight to drive chemical reactions such as water splitting to produce oxygen and hydrogen. It is a scalable technology that requires lighter equipment and utilizes resources available on the moon. ABSTRACT The discovery
Ranjani Kalyan, Thomas D. Small, Gregory F. Metha, Mahmoud Adel Hamza, Thomas J. O'Dea, Yideng Shen, Cameron J. Shearer   +6 more
wiley   +1 more source

Potential Structural Materials and Design Concepts for Light Airplanes [PDF]

Potential structural materials and design considerations for helicopters and light general ...
Pazmany, L., Prentice, H., Tietge, F., Waterman, C.   +3 more
core   +1 more source

Exploring the Potential of Zero‐Dimensional Carbon Nanomaterials in Photoluminescent, Electrochemiluminescent and Electrochemical Sensors

Advanced Materials Interfaces, EarlyView.
Zero‐dimensional carbon nanomaterials are presented as multifunctional platforms linking structure, property, and sensing performance. Surface engineering and heteroatom doping modulate electron‐transfer and luminescent behavior, enabling electrochemical, photoluminescent, and electrochemiluminescent detection. Fundamental design principles, analytical
Gustavo Martins, Jeferson Luiz Gogola, Ava Gevaerd, Cristiane Kalinke, Paulo Roberto de Oliveira, Fabio Roberto Caetano, Bruno Campos Janegitz, Márcio Fernando Bergamini, Luiz Humberto Marcolino‐Junior   +8 more
wiley   +1 more source

Evaluation of ceramics for stator application: Gas turbine engine report [PDF]

Current ceramic materials, component fabrication processes, and reliability prediction capability for ceramic stators in an automotive gas turbine engine environment are assessed.
Havstad, P. H., Trela, W.
core   +1 more source

Energy Band Alignment and Electro‐Optical Behavior of Nearly Unstrained Monolayer MoS2 Heterostructures With GaN

Advanced Materials Interfaces, EarlyView.
Large size (∼100 µm) monolayer MoS2 grown by LPI‐CVD on n‐GaN exhibit a high n‐type doping, very low strain, and a type‐I band alignment at MoS2/GaN interface. Photocurrent measurements under illumination with photon energies from ∼2 to ∼5 eV show superior electro‐optical performances of these MoS2/n‐GaN heterojunctions as compared to Ni/n‐GaN devices ...
Salvatore Ethan Panasci, Emanuela Schilirò, Giuseppe Greco, Patrick Fiorenza, Fabrizio Roccaforte, Fiorenza Esposito, Igor Píš, Federica Bondino, Antonino Madonia, Marco Cannas, Simonpietro Agnello, Luca Seravalli, Filippo Giannazzo   +12 more
wiley   +1 more source

Topological Point Defects in SmC* Liquid Crystals Under Mechanical Disturbance

Advanced Materials Interfaces, EarlyView.
Tangetial air jet shear inducess island formation and nucleates topological point defects in uniform SmC films. Island bounded by edge dislocation loops shrink and transform into isolated point defects under continued shear. Mechanical perturbatio provides a controllable route for defect engineering in smectric liquid crystal thin films.
Gunganist Kongklad, Vandana Molahalli, Apichart Pattanaporkratana, Nattaporn Chattham   +3 more
wiley   +1 more source

Injection molding of metallic silicon.

Journal of the Ceramic Association, Japan, 1985
Yasunari KANEKO, Masatoshi SATO, Katuyoshi SAITOH, Toshiya TANAKA   +3 more
openaire   +2 more sources

Vat Polymerization 3D Printing for Controlled Drug Release Applications

Advanced Materials Technologies, EarlyView.
ABSTRACT Vat polymerization (VP) 3D printing, a light‐based additive manufacturing technique, has emerged as a promising technique for fabricating complex drug delivery systems with high precision and spatial resolution. This layer‐by‐layer manufacturing process enables the creation of intricate geometries and customizable architectures, which are ...
Hafiz Busari, O. Thompson Mefford, M. Aaron Vaughn   +2 more
wiley   +1 more source

Assessment of the hardness of different orthodontic wires and brackets produced by metal injection molding and conventional methods. [PDF]

Dent Res J (Isfahan), 2017
Alavi S, Kachuie M.
europepmc   +1 more source