Results 101 to 110 of about 2,843,453 (292)
EcoEnergy, EarlyView.This review highlights phase control, facet control, and atomic vacancy engineering as key strategies to enhance charge transport, light harvesting, and surface activity in PEC photoanodes. ABSTRACT Photoelectrochemical (PEC) water splitting is a promising approach for converting solar energy into hydrogen, yet the performance of transition metal oxide
Seonmi Ko +5 more
wiley +1 more source
Fabrication of Biochips with Micro Fluidic Channels by Micro End-milling and Powder Blasting
Sensors, 2008 For microfabrications of biochips with micro fluidic channels, a large number of microfabrication techniques based on silicon or glass-based Micro-Electro-Mechanical System (MEMS) technologies were proposed in the last decade.
Dong Sam Park, Tae Il Seo, Dae Jin Yun
doaj
Hydride Materials for Advanced Electrochemical Energy Storage: Progress and Perspectives
EcoEnergy, EarlyView.Hydrides are emerging as functional materials for low‐carbon electrochemical energy storage. Complex hydrides provide polyanionic electrolyte frameworks for all‐solid‐state, Li–S, and multivalent batteries; hydride ion conductors enable H− transport for emerging hydride‐based cells; and metal hydrides offer established electrode chemistries for Ni–MH ...
Taehyun Kim +4 more
wiley +1 more source
Niobium‐Based Chalcogenides as Emerging Electrode Materials for Rechargeable Batteries
EcoEnergy, EarlyView.This review highlights recent advances in Nb‐based TMCs, covering their structure‐property relationships, synthesis strategies, electrochemical mechanisms, and energy‐storage applications. Emerging approaches including defect engineering, operando characterization, DFT modeling, and AI‐assisted design are discussed to accelerate the development of high‐
Narasimharao Kitchamsetti +3 more
wiley +1 more source
Injection molding parameter optimization using the Taguchi method for highest green strength for bimodal powder mixture with SS316L in PEG and PMMA [PDF]
, 2008 Injection molding parameters for the highest green strength of the metal powder mixture has been optimized using L27 (313) Taguchi orthogonal array. Parameters optimized are the injection pressure, injection temperature, powder loading, mold temperature,
Amin, S. Y. M. +5 more
core
EcoEnergy, EarlyView.Schematic illustration comparing the charge transfer dynamics and catalytic reaction over the (left) pristine carbon nitride and (right) Bi‐doped carbon nitride photocatalysts. In the pristine system, random charge diffusion and rapid recombination limit catalytic efficiency. In contrast, the Bi‐doped system establishes a robust internal electric field
Joel Jie Foo +5 more
wiley +1 more source
CAE for Advanced Injection Molding Technologies
, 2019 Injection molding is one of the most popular polymer processing methods and has been used to mass produce plastics products for many decades. However, due to increasingly stringent requirements and higher customer expectations, conventional injection ...
Chang, Rong-Yeu;Huang, Chao-Tsai (CT)
core +1 more source
ENERGY &ENVIRONMENTAL MATERIALS, EarlyView.A one‐step gas‐phase synthesis directly assembles amorphous Si nanoparticles with few‐layer graphene heterostructures via in‐flight mixing. Compositions with only 15 wt.% FLG deliver ~2800 mAh g−1 (Si + FLG) at 0.05 C and retain ~1400 mAh g−1 after 100 cycles at a high cycling rate of 1 C, enabled by a percolated, strain‐buffering graphene network that
Muhammad Ali +5 more
wiley +1 more source
Electrochemical behavior of injection molded gas and water atomized 17-4PH stainless steel powder
, 2017 This paper describes the electrochemical behavior of injection molded 17-4PH stainless steel gas and water atomized powder. Gas and water atomized stainless steel powders were injection molded with wax based binder.
core