Results 21 to 30 of about 1,452,147 (241)
Journal of Materials Research and Technology, 2019 Composite with aluminium 6061 matrix using red mud reinforcement to reduce the cost have been fabricated by stir casting method. A stirring arrangement has been used to ensure the uniform distribution. Scanning electron microscopy has been used to verify
Narender Panwar, Amit Chauhan
doaj +1 more source
Archives of Foundry Engineering, 2017 In this study, Taguchi method is used to find out the effect of micro alloying elements like vanadium, niobium and titanium on the hardness and tensile strength of the normalized cast steel.
Chokkalingam B. +4 more
doaj +1 more source
Micro Drilling of Single Crystal SiC Using Polycrystalline Diamond Tool [PDF]
한국정밀공학회지, 2021 Silicon carbide (SiC) has been used as a material for semi-conductor, molds, and micro-electro-mechanical systems (MEMS) because of its superior thermal, electrical, and mechanical properties.
Ui Seok Lee +3 more
doaj +1 more source
Archives of Metallurgy and Materials, 2016 The influence of applied loads between 0.09807 N and 0.9807 N on measured values of micro-hardness was evaluated by Meyer’s index n, proportional specimen resistance model (PSR) and Hays – Kendall methods, Total Dispersion Zone and Analysis of Variance ...
Petrík J.
doaj +1 more source
Applied Sciences, 2020 In order to improve the performance of the cladding layer, this study used the Taguchi orthogonal design to investigate the influence of laser power, scanning speed, gas flow, and SiC powder ratio on the micro-hardness and wear volume of the cladding ...
Guofu Lian +4 more
doaj +1 more source
Hardness determination of bio-ceramics using laser-induced breakdown spectroscopy. [PDF]
, 2011 Laser-Induced Breakdown Spectroscopy (LIBS) was applied to the analysis of bioceramic samples. The relationship between sample hardness and LIBS plasma properties was investigated, with comparison to conventional Vickers hardness measurements.
Moser, D. +23 more
core +1 more source
A new method for hardness determination from depth sensing indentation tests [PDF]
, 1996 A new semiempirical formula is developed for the hardness determination of the materials from depth sensing indentation tests. The indentation works measured both during loading and unloading periods are used in the evaluation.
Juhász, A. +2 more
core +1 more source
Micro-hardness variation of micro-phases during spheroidisation of AISI4340 steel
Cogent Engineering, 2021 AISI4340 steel is the medium carbon low-alloy steel has got excellent prominence as a construction material. This steel is spheroidised on heating to the intercritical temperature range by different time intervals with the objective of increasing the ...
Harisha S R +4 more
doaj +1 more source
Surface Modification of Red Brass Alloy by Using Laser Technique [PDF]
Engineering and Technology Journal, 2016 Laser shock processing technique was performed on red brass alloy type C83300 specimens for the purpose ofstudy its effect on the mechanical properties such as micro-hardness and surface roughness. LSP experimental setup system involved Q-switched Nd:YaG
Abdulhadi Kadhim +2 more
doaj +1 more source
Vestnik Samarskogo Gosudarstvennogo Tehničeskogo Universiteta. Seriâ: Fiziko-Matematičeskie Nauki, 2007 The damage of the sliding friction surfaces of constructional steel 40Kh over the stainless steel 12Kh18N10T is researched. From the comparison of the damage processes for steel 40Kh in its initial annealed state, after the laser and laser-ultrasonic ...
G. D. Gureev, D. M. Gureev
doaj +1 more source