Results 41 to 50 of about 1,734,379 (203)

Parametric behaviour optimisation of macro and micro hardness for heat treated Al 6061-red mud composite

open access: yes, 2019
Composite with aluminium 6061 matrix using red mud reinforcement to reduce the cost have been fabricated by stir casting method. A stirring arrangement has been used to ensure the uniform distribution. Scanning electron microscopy has been used to verify
Narender Panwar, Amit Chauhan
core   +1 more source

GeS as an Emerging OTS Material: Atomic Structure and Modeling of ON/OFF Switching

open access: yesAdvanced Functional Materials, EarlyView.
The structural puzzle of glassy GeS, an advanced memory‐selector material, has finally been disentangled, revealing a patchwork of mixed tetrahedral and trigonal species. Under a high electric field, over‐ and under‐coordinated Ge and S defects, together with three‐membered rings, form an interconnected network associated with localized and extended ...
Andrey Tverjanovich   +13 more
wiley   +1 more source

DEVELOPMENT OF MICRO-HARDNESS AND WEAR PERFORMANCES OF BIOMEDICAL TITANIUM

open access: yes, 2018
In the present work, the influence of thermal oxidation (TO) process on the micro-hardness and wear performances of a pure titanium (Ti) was studied.
T. Mohammed, Mohsin, Mohsin T. Mohammed
core   +2 more sources

Configuration‐Encoded Cell Alignment by Light‐Gated Silicon Photovoltaic Microcell Arrays

open access: yesAdvanced Functional Materials, EarlyView.
Light‐gated silicon photovoltaic microcells convert pulsed illumination into localized electrical cues. Arranging otherwise similar microcells into four‐lobed, six‐lobed, or circular patterns directs fibroblasts into corresponding local arrangements without wired stimulation.
Yifan Tao   +7 more
wiley   +1 more source

A new method for hardness determination from depth sensing indentation tests [PDF]

open access: yes, 1996
A new semiempirical formula is developed for the hardness determination of the materials from depth sensing indentation tests. The indentation works measured both during loading and unloading periods are used in the evaluation.
Juhász, A.   +2 more
core   +1 more source

A Miniaturized Autonomous Thermomagnetic Generator

open access: yesAdvanced Functional Materials, EarlyView.
Micro, autonomous and high power thermomagnetic generator operating between a heat dissipator and a processor. ABSTRACT Thermomagnetic generators (TMG) are promising devices for converting low‐grade waste heat into electricity. Self‐actuation using permanent magnets is the key to autonomy.
Morgan Almanza   +11 more
wiley   +1 more source

Effect of laser peening on residual stress and micro-hardness of TC4 titanium alloy

open access: yes, 2013
Laser peening offers potential advantages over conventional peen technologies in terms of the depth of the residual stresses that can be induced, and improvements in surface micro-hardness.
Li L(李论)   +3 more
core  

Ultra‐Thin Tow‐Based Discontinuous Composites—Material Overview and Aspirations

open access: yesAdvanced Functional Materials, EarlyView.
Tow‐based discontinuous composites made from ultra‐thin tapes offer outstanding in‐plane mechanical properties. This material, inspired by Nacre, has high volume fraction of tapes exceeding 90 % and allows for quasi‐isotropic material plates less than 100 micrometer in thickness.
Ioannis Katsivalis   +8 more
wiley   +1 more source

Optimization of process parameters for electroless Ni–Co–P coating deposition to maximize micro-hardness

open access: yes, 2019
The present study investigates optimisation of microhardness of electroless Ni–Co–P alloy coating over copper substrate. The microhardness of the coating was significantly higher compared to the substrate.
Subhasish Sarkar (17936828)   +4 more
core  

Effect of curing modes on micro-hardness of dual-cure resin cements

open access: yes, 2011
Objectives The purpose of this study was to evaluate curing degree of three dual-cure resin cements with the elapsed time in self-cure and dual-cure mode by means of the repeated measure of micro-hardness.
Ki-Deok Lee   +4 more
core   +1 more source

Home - About - Disclaimer - Privacy