Results 51 to 60 of about 33,032 (255)
Applied Sciences, 2017 In order to build a better understanding of the relationship between depositing mode and porosity, microstructure, and properties in wire + arc additive manufacturing (WAAM) 2319-Al components, several Al-6.3%Cu deposits were produced by WAAM technique ...
Baoqiang Cong +5 more
doaj +1 more source
Active Corrosion Protection of Sintered AA7075 Aluminum Alloy via Mn Powder Addition
Advanced Engineering Materials, EarlyView.AA7075 containing Mn‐rich particles is fabricated via spark plasma sintering using AA7075 and Mn powders. Corrosion resistance is evaluated through dip‐and‐dry tests using 0.1 M NaCl (pH 6.0), and mass loss decreases with increasing Mn addition. Mn‐rich particles function as a source of Mn ions, and formation of Mn‐accumulation films on Cu‐containing ...
Ko Ebina, Masashi Nishimoto, Izumi Muto
wiley +1 more source
Pakistan Armed Forces Medical Journal, 2015 Objective: To determine the micro hardness of novel Pakistani manufactured osteosynthetic titanium bone mini plates (MPP) and imported osteosynthetic titanium bone mini plates (MPG) in body like conditions. Study Design: Descriptive study.
Rabia Anwar +6 more
doaj +2 more sources
Advanced Engineering Materials, EarlyView.Manufacturing problems such as heat treatment‐induced cracking hinder the widespread application of the laser powder bed fusion (LPBF) process to superalloys. In this study, cracks in the LPBF components of Inconel 738LC superalloy are characterized after heat treatment at various temperature ranges, revealing two distinct cracking behaviors.
Kosuke Kuwabara +4 more
wiley +1 more source
THE AUTOMATIC TESTERS IN MICROHARDNESS MEASUREMENT AND ISE EFFECT
Acta Metallurgica Slovaca, 2016 The measurement of micro-hardness with the applied loads 0.09807 N, 0.24518 N, 0.49035 N and 0.9807 N has been carried out by three automatic and one manually-operated micro-hardness testers.
Jozef Petrík +4 more
doaj +1 more source
Micro hardness measurements on lead silicate glass
Bulletin of Materials Science, 1998 The synthesis of lead silicate glass suitable for fabrication of compression type glass to metal seals has been studied with varying amounts of modifier ions (Na, K and Ba). A three-stage heating schedule was evolved for the preparation of glass. While, some of the constituents were taken in the form of oxides, the others were either in the form of ...
V K Shrikhande +4 more
openaire +2 more sources
Additive Manufacturing of Alumina‐Reinforced Elastomers
Advanced Engineering Materials, EarlyView.Vat‐photopolymerized elastomers reinforced with platelet‐shaped alumina exhibited preferential orientation, reduced porosity, and significantly enhanced mechanical performance. A 3 wt% platelet loading increased tensile strength from 12.4 to 45.7 MPa, highlighting the critical role of filler morphology in elastomeric VPP composites.
Majid Barzegar Keyvani +6 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This review comprehensively evaluates extrusion‐based additive manufacturing for advanced ceramics, detailing feedstock options and key process parameters. By critically addressing defect mechanisms like porosity and cracking, the work highlights optimization strategies through machine learning and advanced postprocessing.
Meisam Bakhtiari +4 more
wiley +1 more source
Journal of Baghdad College of Dentistry, 2014 Background: Alterations in the microhardness and roughness are commonly used to analyze the possible negative effects of bleaching products on restorative materials.
Noor S Nadhum, Ali H Al-Khafaji
doaj
Advanced Engineering Materials, EarlyView.Different Al/Al bimetals with a single engineered interface reveal how mechanical mismatch governs fatigue crack growth under cyclic loading. Additionally, loading–unloading–reloading tests link the microyielding behavior to the fatigue crack growth resistance, while crack‐path analysis reveals toughening mechanisms at the interface, highlighting ...
Sebastian Vollath +2 more
wiley +1 more source