Results 51 to 60 of about 1,483,235 (290)
Advanced Engineering Materials, EarlyView.Scandium (Sc)‐doped AlCoCrFeMo HEA coatings are fabricated via flame spraying with 0.1, 0.3, and 0.5 wt% Sc additions. Among these, the HEA‐Sc0.3 coating exhibits the highest corrosion resistance, indicated by a more positive corrosion potential and lower current density.
Pankaj Kumar +7 more
wiley +1 more source
In Vitro Evaluation of Enamel Microhardness after Application of Two Types of Fluoride Varnish [PDF]
Journal of Clinical and Diagnostic Research, 2017 Introduction: Use of fluoride compounds is one of the most effective ways of preventing decay and among these varnishes have high acceptance among different fluoride products.
Fatemeh Molaasadolah +3 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Manufacturing problems such as heat treatment‐induced cracking hinder the widespread application of the laser powder bed fusion (LPBF) process to superalloys. In this study, cracks in the LPBF components of Inconel 738LC superalloy are characterized after heat treatment at various temperature ranges, revealing two distinct cracking behaviors.
Kosuke Kuwabara +4 more
wiley +1 more source
EVALUATION OF ENAMEL MICROHARDNESS AFTER APPLICATION OF THE PRE-REACTED GLASS IONOMER VARNISH IN PERMENANT TEETH (IN VITRO STUDY) [PDF]
Alexandria Dental JournalIntroduction: Surface pre-reacted glass ionomer varnish (S-PRG) is a product that contains filler particles incorporated into resin material and promising in arresting pits and fissure caries of permanent teeth.Objectives: Evaluate and compare the micro ...
Ahmed Yassin, Nadia Wahba, Reham Soliman
doaj +1 more source
Additive Manufacturing of Alumina‐Reinforced Elastomers
Advanced Engineering Materials, EarlyView.Vat‐photopolymerized elastomers reinforced with platelet‐shaped alumina exhibited preferential orientation, reduced porosity, and significantly enhanced mechanical performance. A 3 wt% platelet loading increased tensile strength from 12.4 to 45.7 MPa, highlighting the critical role of filler morphology in elastomeric VPP composites.
Majid Barzegar Keyvani +6 more
wiley +1 more source
Effect of a multi-layer infection control barrier on the micro-hardness of a composite resin
Journal of Applied Oral Science, 2012 OBJECTIVE: The aim of this study was to evaluate the effect of multiple layers of an infection control barrier on the micro-hardness of a composite resin. MATERIAL AND METHODS: One, two, four, and eight layers of an infection control barrier were used to
In-Nam Hwang +5 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Different Al/Al bimetals with a single engineered interface reveal how mechanical mismatch governs fatigue crack growth under cyclic loading. Additionally, loading–unloading–reloading tests link the microyielding behavior to the fatigue crack growth resistance, while crack‐path analysis reveals toughening mechanisms at the interface, highlighting ...
Sebastian Vollath +2 more
wiley +1 more source
DEVELOPMENT OF MICRO-HARDNESS AND WEAR PERFORMANCES OF BIOMEDICAL TITANIUM
, 2021 In the present work, the influence of thermal oxidation (TO) process on the micro-hardness and wear performances of a pure titanium (Ti) was studied.
Mohsin Mohammed
core +2 more sources
ISE of Precious Metals: Au, Ag, Pd, and Pt
MetalsPrecious metals play an important role in various fields, from industry to jewelry and finance. In the industrial field, it is often necessary to know their mechanical properties. Micro-hardness measurement is a suitable test.
Lenka Girmanová +5 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Solvate ionic liquids lubrication reduced the coefficient of friction by ∼60% compared to dry sliding, reaching steady‐state values as low as 0.04–0.05. Corrosion weight‐loss measurements in 1 M HCl further demonstrated significant inhibition behavior, with only 100 ppm of [Li(G3)][TFSI] (∼68.5 μL/L) reducing corrosion‐product weight loss by 63 ...
Sameh Dabees +6 more
wiley +1 more source