Results 61 to 70 of about 33,032 (259)

Kekerasan mikro enamel gigi permanen muda setelah aplikasi bahan pemutih gigi dan pasta remineralisasi (Enamel micro hardness of young permanent tooth after bleaching and remineralization paste application)

Dental Journal, 2014
Background: Studies showed that bleaching agent had demineralization effect to enamel, and encourage use of remineralization paste after bleaching treatment especially in young permanent tooth which in post-eruptive enamel maturation.
Budianto Liwang, Irmawati Irmawati, Els Budipramana   +2 more
doaj   +1 more source

Enhancing Fatigue Crack Growth Resistance in Heterostructured Aluminum Bimetals by Tailored Interface Design

Advanced Engineering Materials, EarlyView.
Different Al/Al bimetals with a single engineered interface reveal how mechanical mismatch governs fatigue crack growth under cyclic loading. Additionally, loading–unloading–reloading tests link the microyielding behavior to the fatigue crack growth resistance, while crack‐path analysis reveals toughening mechanisms at the interface, highlighting ...
Sebastian Vollath, Philip Manuel Pohl, Heinz Werner Höppel   +2 more
wiley   +1 more source

Superlubricity and Corrosion Inhibition Properties of Solvate Ionic Liquids in Hybrid Carbon Fiber Reinforced Plastic–Steel Interfaces

Advanced Engineering Materials, EarlyView.
Solvate ionic liquids lubrication reduced the coefficient of friction by ∼60% compared to dry sliding, reaching steady‐state values as low as 0.04–0.05. Corrosion weight‐loss measurements in 1 M HCl further demonstrated significant inhibition behavior, with only 100 ppm of [Li(G3)][TFSI] (∼68.5 μL/L) reducing corrosion‐product weight loss by 63 ...
Sameh Dabees, Timothy Harte, Bhagya Dharmasiri, Y. Athulya Wickramasingha, David J. Hayne, Daniel J. Eyckens, Luke C. Henderson   +6 more
wiley   +1 more source

Stretching the Printability Metric in Direct‐Ink Writing with Highly Extensible Yield‐Stress Fluids

Advanced Functional Materials, EarlyView.
This study introduces “drawability” as a new metric for assessing printability in direct‐ink writing, focusing on gap‐spanning performance and speed robustness. By designing yield‐stress fluids with high extensibility, we demonstrate that extensional strain‐to‐break significantly enhances printability.
Chaimongkol Saengow, Samya Sen, Joaquin Yus, Eliza E. Lovrich, Amanda G. Hoika, Kelly M. Chang, Arielle A. Pfeil, Nellie Haug, Amy J. Wagoner Johnson, Randy H. Ewoldt   +9 more
wiley   +1 more source

Micro-hardness measurement of photopolymer in stereolithography.

Journal of Photopolymer Science and Technology, 1997
The curing of liquid photopolymer is determined by the exposure (optical energy) deposited. In laser stereolithography, laser exposure is considered as non-homogenous within the radiation area. In order to investigate the difference of the cure degree within the cross section of a single cured strand, a micro-structure was evaluated by hardness ...
XU, Yi, IMAMURA, Masato, NAKAGAWA, Takeo
openaire   +2 more sources

Laser‐Induced Graphene from Waste Almond Shells

Advanced Functional Materials, EarlyView.
Almond shells, an abundant agricultural by‐product, are repurposed to create a fully bioderived almond shell/chitosan composite (ASC) degradable in soil. ASC is converted into laser‐induced graphene (LIG) by laser scribing and proposed as a substrate for transient electronics.
Yulia Steksova, Anna Chiara Bressi, Marina Galliani, Attilio Marino, Gianni Ciofani, Eduardo Machado‐Charry, Hilda Gomez Bernal, Alessandra Francini, Luca Sebastiani, Francesco Greco   +9 more
wiley   +1 more source

Investigating the Fracture Toughness and Mechanical Properties of the Two-Layer Al 1050/Mg AZ31B Sheets Fabricated by the Roll Bonding, Considering the Annealing Temperature Effect [PDF]

Iranian Journal of Materials Science and Engineering
This study presents the manufacturing of Al 1050/Mg AZ31B bimetallic sheets using the cool roll bonding process, followed by an investigation of the effect of annealing temperature on mechanical properties and microstructural features.
Payam Tayebi, ramin hashemi
doaj  

Advances in Sustainable and Wearable Textile Based Soft Robotics

Advanced Functional Materials, EarlyView.
This Review examines advances in wearable textile‐based soft robotics, focusing on sustainable materials, integrated sensing, and scalable actuation. It discusses manufacturing and system integration across healthcare, assistive robotics, prosthetics, and human–machine interfaces, and highlights key challenges in circular design, including life‐cycle ...
Zahir Abbas, Marzia Dulal, Sophia K. Novoselov, Victoria K. Novoselov, Kostya S. Novoselov, Shaila Afroj, Nazmul Karim   +6 more
wiley   +1 more source

Influence of Different Temperatures on the Polymerization Pre- and Post-Cured of Various Resin Materials

Dentistry 3000
Objective: To evaluate and compered the effect of different temperatures (5°C, 37°C and room temp. ±23°C) pre- cured and post-cured for three universal- Chroma composite materials (Hybrid-Nano fillers, Supra-Nano, Nano filler) on the polymerization ...
Fanar Turki Al-Jadwaa, Mhammad Munthir Abdurazzaq, Emad Farhan Alkhalidi   +2 more
doaj   +1 more source

Electrospun Wood‐Derived Biopolymers as Electrodes in Electrochemical Energy Storage Technologies

Advanced Functional Materials, EarlyView.
Electrospinning transforms wood‐derived cellulose and lignin into architecturally defined, binder‐free carbon electrodes with tuneable porosity and functionality. This review shows how fibre design enables decoupled charge and mass transport, enhancing performance across battery systems, while identifying key challenges in spinnability, scalability ...
Michael W. Thielke, Hattie R. Chisnall, Jesus Vazquez Chavez, Ana B. Jorge Sobrido   +3 more
wiley   +1 more source