Results 61 to 70 of about 4,233 (200)
Case Studies in Thermal EngineeringThis study presents the design and experimental validation of two-dimensional (2D) and pseudo three-dimensional (P3D) microchannel heat sinks optimized through single-objective and multiobjective topology optimization via the solid isotropic material ...
Guangzhao Yang +8 more
doaj +1 more source
Experimental investigation of two-phase pressure drop in a microchannel [PDF]
, 2009 This paper was presented at the 2nd Micro and Nano Flows Conference (MNF2009), which was held at Brunel University, West London, UK. The conference was organised by Brunel University and supported by the Institution of Mechanical Engineers, IPEM, the ...
2nd Micro and Nano Flows Conference (MNF2009) +3 more
core
Flow boiling in rectangular microchannels: 1-D modelling of the influence of inlet resistance on flow reversal [PDF]
, 2014 This paper was presented at the 4th Micro and Nano Flows Conference (MNF2014), which was held at University College, London, UK. The conference was organised by Brunel University and supported by the Italian Union of Thermofluiddynamics, IPEM, the ...
4th Micro and Nano Flows Conference (MNF2014) +3 more
core
Flow Boiling in Silicon Microchannel Heat Sinks
2008 Twenty-fourth Annual IEEE Semiconductor Thermal Measurement and Management Symposium, 2008 The local flow boiling heat transfer and pressure drop in microchannel heat sinks are investigated with a dielectric fluid, Fluorinert FC-77. The effect of channel size on flow boiling is studied for mass fluxes ranging from 250 to 1600 kg/m2s for seven different test pieces consisting of parallel microchannels with nominal widths ranging from 100 to ...
Harirchian, Tannaz, Garimella, Suresh V.
openaire +3 more sources
Liquid cooling of non-uniform heat flux of chip circuit by submicrochannels [PDF]
, 2014 Sumbmicrochannels have been placed on the hotspots in a non-uniform heat generated chip circuit to increase the liquid/solid interaction area and then to enhance the heat dissipation.
AlWaaly, Ahmed A. Y. +2 more
core
Study of thermal bubble motion in microchannel [PDF]
, 2009 This paper was presented at the 2nd Micro and Nano Flows Conference (MNF2009), which was held at Brunel University, West London, UK. The conference was organised by Brunel University and supported by the Institution of Mechanical Engineers, IPEM, the ...
2nd Micro and Nano Flows Conference (MNF2009) +4 more
core
Evolutionary Optimization of Electronic Circuitry Cooling Using Nanofluid [PDF]
, 2012 Liquid cooling electronics using microchannels integrated in the chips is an attractive alternative to bulky aluminum heat sinks. Cooling can be further enhanced using nanofluids.
Mital, Manu
core +3 more sources
Numerical investigation of aspect ratio effect on thermal parameters in laminar nanofluid flow in microchannel heat sink [PDF]
, 2011 This paper was presented at the 3rd Micro and Nano Flows Conference (MNF2011), which was held at the Makedonia Palace Hotel, Thessaloniki in Greece.
3rd Micro and Nano Flows Conference (MNF2011) +2 more
core
Similarities and differences between flow boiling in microchannels and pool boiling [PDF]
, 2009 This paper was presented at the 2nd Micro and Nano Flows Conference (MNF2009), which was held at Brunel University, West London, UK. The conference was organised by Brunel University and supported by the Institution of Mechanical Engineers, IPEM, the ...
2nd Micro and Nano Flows Conference (MNF2009) +1 more
core
Numerical analysis and parametric study of multilayered microchannel heat sinks
Advances in Mechanical Engineering, 2015 A three-dimensional solid–fluid conjugated model is used to investigate and optimize the performances of two-, three-, and four-layered microchannel heat sinks. In the optimization process, constraints of fixed total pumping power and fixed total channel
Lin Lin +3 more
doaj +1 more source